X-On Electronics has gained recognition as a prominent supplier of MCP19118-E/MJ Switching Controllers across the USA, India, Europe, Australia, and various other global locations. MCP19118-E/MJ Switching Controllers are a product manufactured by Microchip. We provide cost-effective solutions for Switching Controllers, ensuring timely deliveries around the world.
We are delighted to provide the MCP19118-E/MJ from our Switching Controllers category, at competitive rates not only in the United States, Australia, and India, but also across Europe and beyond. A long established and extensive electronic component distribution network has enhanced our global reach and dependability, ensuring cost savings through prompt deliveries worldwide. Client satisfaction is at the heart of our business, where every component counts and every customer matters. Our technical service team is ready to assist you. From product selection to after-sales support, we strive to deliver a seamless and satisfying experience. Are you ready to experience the best in electronic component distribution? Contact X-ON Electronics today and discover why X-On are a preferred choice for the MCP19118-E/MJ and other electronic components in the Switching Controllers category and beyond.
MCP19118/19 Digitally-Enhanced Power Analog Controller with Integrated Synchronous Driver Synchronous Buck Features: Microcontroller Features: Precision 8 MHz Internal Oscillator Block: Input Voltage: 4.5V to 40V - Factory Calibrated Output Voltage: 0.5V to 3.6V Interrupt Capable - Greater than 3.6V requires external divider -Firmware Switching Frequency: 100 kHz to 1.6 MHz - Interrupt-on-Change Pins Quiescent Current: 5 mA Typical Only 35 Instructions to Learn High-Drive: 4096 Words On-Chip Program Memory - +5V Gate Drive High-Endurance Flash: - 1A/2A Source Current - 100,000 Write Flash Endurance - 1A/2A Sink Current - Flash Retention: >40 years Low-Drive: Watchdog Timer (WDT) with Independent - +5V Gate Drive Oscillator for Reliable Operation - 2A Source Current Programmable Code Protection - 4A Sink Current In-Circuit Debug (ICD) via Two Pins (MCP19119) Peak Current Mode Control In-Circuit Serial Programming (ICSP) via Two Differential Remote Output Sense Pins QEC-100 Qualified 11 I/O Pins and One Input-Only Pin (MCP19118) Multiple Output Systems: - Three Open-Drain Pins - Master or Slave 14 I/O Pins and One Input-Only Pin (MCP19119) - Frequency Synchronized - Three Open-Drain Pins Configurable Parameters: Analog-to-Digital Converter (ADC): - Overcurrent Limit - 10-Bit Resolution - Input Undervoltage Lockout - 12 Internal Channels - Output Overvoltage - Eight External Channels - Output Undervoltage Timer0: 8-Bit Timer/Counter with 8-Bit Prescaler - Internal Analog Compensation Enhanced Timer1: - Soft Start Profile - 16-Bit Timer/Counter with Prescaler - Synchronous Driver Dead Time - Two Selectable Clock Sources - Switching Frequency Timer2: 8-Bit Timer/Counter with Prescaler Thermal Shutdown - 8-Bit Period Register 2 TM I C Communication: - 7-Bit Address Masking - Two Dedicated Address Registers TM - SMBus/PMBus Compatibility 2014 Microchip Technology Inc. DS20005350A-page 1MCP19118/19 Pin Diagram 24-Pin QFN (MCP19118) 1 GPA0 V 18 DD 2 BOOT GPA1 17 3 GPA2 16 HDRV MCP19118 4 GPA3 15 PHASE 5 GPA7 V 14 DR EXP-25 6 GPA6 13 LDRV DS20005350A-page 2 2014 Microchip Technology Inc. GPA5/MCLR 7 GPB2 24 GPA4 8 GPB1 23 GPB0 9 -V 22 SEN 10 GND 21 +V SEN V 11 20 +I IN SEN 12 P 19 -I GND SEN