Chip Multilayer Ceramic Capacitors for Automotive GCM31C5C2A104JE02 (1206, C0G:EIA, 0.1uF, DC100V) : packaging code Reference Sheet 1.Scope This product specification is applied to Chip Multilayer Ceramic Capacitors used for Automotive Electronic equipment. 2.MURATA Part NO. System (Ex.) GCM 31 C 5C 2A 104 J E02 L (1)L/W (2)T (3)Temperature (4)Rated (5)Nominal (6)Capacitance (7)Muratas Control (8)Packaging Code Dimensions Dimensions Characteristics Voltage Capacitance Tolerance Code 3. Type & Dimensions (Unit:mm) (1)-1 L (1)-2 W (2) T e g 3.20.2 1.60.2 1.60.2 0.3 to 0.8 1.5 min. 4.Rated value (3) Temperature Characteristics Specifications and Test (4) (6) (Public STD Code):C0G(EIA) (5) Nominal Methods Rated Capacitance (Operating Temp. coeff Temp. Range Capacitance Voltage Tolerance Temp. Range) orCap. Change (Ref.Temp.) 25 to 125 C 030 ppm/C DC 100 V 0.1 uF 5 % -55 to 125 C (25 C) 5.Package mark (8) Packaging Packaging Unit f180mm Reel L 2000 pcs./Reel EMBOSSED W8P4 f330mm Reel K 6000 pcs./Reel EMBOSSED W8P4 Product specifications in this catalog are as of Apr.12,2019,and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering. Please read rating and Cautions first. GCM31C5C2A104JE02-01 1AEC-Q200 Murata Standard Specification and Test Methods No AEC-Q200 Test Item Specification. AEC-Q200 Test Method Pre-and Post-Stress 1 - Electrical Test 2 High Temperature The measured and observed characteristics should satisfy the Solder the capacitor on the test substrate(glass epoxy board). Exposure (Storage) specifications in the following table. Set the capacitor for 1000+/-12h at 150+/-3. Appearance No defects or abnormalities Set for 24+/-2h at room temperature, then measure. Capacitance Within +/-1% or +/-0.1pF Change (Whichever is larger) Q 30pFmin. : Q 350 10pF and over, 30pF and below:Q 275+5C/2 10pFmax.: Q 200+10C C: Nominal Capacitance(pF) I.R. Within the specified initial value 25 3 Temperature Cycling The measured and observed characteristics should satisfy the Solder the capacitor on the test substrate(glass epoxy board). specifications in the following table. Perform cycle test according to the four heat treatments listed Appearance No defects or abnormalities in the following table. Set for 24+/-2h at room temperature, then measure. Capacitance Within +/-1% or +/-0.1pF Change (Whichever is larger) Cycles Step Time(min) 1000(for C) 300(for 5G) 1 15+/-3 -55+0/-3 -55+0/-3 Q Within the specified initial value 2 1 Room Room 3 15+/-3 125+3/-0 150+3/-0 4 1 Room Room I.R. Within the specified initial value 25 4 Destructive No defects or abnormalities Per EIA-469. Physical Analysis 5 Moisture Resistance The measured and observed characteristics should satisfy the Solder the capacitor on the test substrate(glass epoxy board). specifications in the following table. Apply the 24h heat (25 to 65) and humidity (80%RH to 98%RH) treatment shown below, 10 consecutive times. Appearance No defects or abnormalities Set for 24+/-2h at room temperature, then measure. Capacitance Within +/-1% or +/-0.1pF Humidity Humidity Temperature Change (Whichever is larger) 8098% 8098% Humidity Humidity Humidity () 9098% 9098% 9098% 70 65 Q 30pFmin. : Q350 60 55 10pF and over, 30pF and below:Q275+5C/2 50 10pFmax.: Q 200+10C 45 40 C: Nominal Capacitance(pF) 35 30 25 20 +10 - 2 15 I.R. Within the specified initial value 10 5 Initial measuremt 25 0 -5 -10 One cycle 24hours 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Hours 6 The measured and observed characteristics should satisfy the Biased Humidity Solder the capacitor on the test substrate(glass epoxy board). specifications in the following table. Apply the rated voltage and 1.3+0.2/-0Vdc (add 6.8k resister) at 85+/-3 and 80%RH to 85%RH humidity for 1000+/-12h. Appearance No defects or abnormalities The charge/discharge current is less than 50mA. Remove and set for 24+/-2h at room temperature, then measure. Capacitance Within +/-3.0% or +/-0.30pF Change (Whichever is larger) Q 30pF and over: Q200 30pF and below: Q100+10C/3 C: Nominal Capacitance(pF) I.R. More than 500M or 25F 25 (Whichever is smaller) JEMCGS-07136 2