RFM products are now Murata products. SF2176E Low-loss RF SAW Filter Surface-mount 3.0 x 3.0 x 1.3 mm Package Complies with Directive 2002/95/EC (RoHS) Pb 433.92 MHz Complies with AEC-Q200 SAW Filter Absolute Maximum Ratings Rating Value Units Input Power Level 10 dBm DC Voltage on any Non-ground Terminal 3 V Operating Temperature Range -40 to +105 C Storage Temperature Range in Tape and Reel -40 to +85 C Usable Temperature Range -40 to 125 C C Solder Reflow Temperature, 10 seconds, 5 cycles maximum 260 SM3030-6 Electrical Characteristics -40 to +85C Characteristic Sym Notes Min Typ Max Units Center Frequency F 433.92 MHz C Maximum Insertion Loss, 433.12 to 434.72 MHz IL 2.2 2.9 dB MAX Amplitude Ripple, 433.12 to 434.72 MHz 0.4 1.0 dB P-P VSWR, 433.12 to 434.72 MHz 1.6 2.0 Attenuation Referenced to 0 dB: 10.00 to 380.00 MHz 58 61 380.00 to 423.42MHz 46 50 443.42 to 453.42 MHz 25 30 dB 453.42 to 460.00 MHz 35 40 460.00 to 700.00 MHz 50 54 700.00 to 1000.00 MHz 42 46 Z Source Impedance 50 S Z Load Impedance 50 L Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator A09, YWWS Standard Reel Quantity Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4.LRI or after the part number indicateslow rate initial productio andEN or indicatesengineering prototypes 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. 2010-2015 by Murata Electronics N.A., Inc. SF2176E (R) 12/9/15 Page 1 of 6 www.murata.comElectrical Characteristics -40 to +105c Characteristic Sym Notes Min Typ Max Units F Center Frequency 433.92 MHz C IL Maximum Insertion Loss, 433.12 to 434.72 MHz 2.2 3.2 dB MAX dB Amplitude Ripple, 433.12 to 434.72 MHz 0.4 1.4 P-P VSWR, S11 S22 1.6 2.0 Attenuation Referenced to 0 dB: 10.00 to 380.00 MHz 58 61 380.00 to 423.42MHz 46 50 443.42 to 453.42 MHz 12 30 dB 453.42 to 460.00 MHz 35 40 460.00 to 700.00 MHz 50 54 700.00 to 1000.00 MHz 42 46 Source Impedance Z 50 S Load Impedance Z 50 L Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator A09, YWWS Standard Reel Quantity Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4.LRI or after the part number indicateslow rate initial productio andEN or indicatesengineering prototypes 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc Filter Test Circuit Connection Terminals Input 2 Output 5 Ground All Others 2010-2015 by Murata Electronics N.A., Inc. www.murata.com SF2176E (R) 12/9/15 Page 2 of 6