NXS0108-Q100 Dual supply translating transceiver open drain auto direction sensing Rev. 1 15 September 2020 Product data sheet 1. General description The NXS0108-Q100 is an 8-bit, dual supply translating transceiver with auto direction sensing, that enables bidirectional voltage level translation. It features two 8-bit input-output ports (An and Bn), one output enable input (OE) and two supply pins (V and V ). V can be supplied at CC(A) CC(B) CC(A) any voltage between 1.2 V and 3.6 V and V can be supplied at any voltage between 1.65 V CC(B) and 5.5 V, making the device suitable for translating between any of the voltage nodes (1.2 V, 1.8 V, 2.5 V, 3.3 V and 5.0 V). Pins An and OE are referenced to V and pins Bn are referenced CC(A) to V . A LOW level at pin OE causes the outputs to assume a high-impedance OFF-state. CC(B) This device is fully specified for partial power-down applications using I . The I circuitry OFF OFF disables the output, preventing the damaging backflow current through the device when it is powered down. This product has been qualified to the Automotive Electronics Council (AEC) standard Q100 (Grade 1) and is suitable for use in automotive applications. 2. Features and benefits Automotive product qualification in accordance with AEC-Q100 (Grade 1) Specified from -40 C to +85 C and from -40 C to +125 C Wide supply voltage range: V : 1.2 V to 3.6 V and V : 1.65 V to 5.5 V CC(A) CC(B) Maximum data rates: Push-pull: 110 Mbps I circuitry provides partial Power-down mode operation OFF Inputs accept voltages up to 5.5 V ESD protection: HBM JESD22-A114E Class 2 exceeds 2.5 kV for A port HBM JESD22-A114E Class 3B exceeds 15 kV for B port CDM JESD22-C101E exceeds 1.5 kV IEC61000-4-2 contact discharge exceeds 8 kV for B port Latch-up performance exceeds 100 mA per JESD 78B Class II DHVQFN package with Side-Wettable Flanks enabling Automatic Optical Inspection (AOI) of solder joints 3. Ordering information Table 1. Ordering information Type number Package Temperature range Name Description Version NXS0108PW-Q100 -40 C to +125 C TSSOP20 plastic thin shrink small outline package 20 leads SOT360-1 body width 4.4 mm NXS0108BQ-Q100 -40 C to +125 C DHVQFN20 plastic dual in-line compatible thermal enhanced SOT764-1 very thin quad flat package no leads 20 terminals body 2.5 4.5 0.85 mmNexperia NXS0108-Q100 Dual supply translating transceiver open drain auto direction sensing 4. Functional diagram OE V V CC(A) CC(B) GATE BIAS R R pu pu An Bn ONE ONE SHOT SHOT aaa-031911 Fig. 1. Functional diagram (one channel) 5. Pinning information 5.1. Pinning NXS0108 terminal 1 index area V 2 19 V CC(A) CC(B) A2 3 18 B2 A3 4 17 B3 A4 5 16 B4 NXS0108 6 15 A5 B5 1 20 A1 B1 A6 7 14 B6 V 2 19 V CC(A) CC(B) A7 8 (1) 13 B7 GND 3 18 A2 B2 A8 9 12 B8 4 17 A3 B3 A4 5 16 B4 6 A5 15 B5 aaa-031913 7 14 A6 B6 Transparent top view A7 8 13 B7 (1) This is not a ground pin. There is no electrical or A8 9 12 B8 mechanical requirement to solder the pad. In case 10 11 OE GND soldered, the solder land should remain floating or aaa-031912 connected to GND. Fig. 2. Pin configuration SOT360-1 (TSSOP20) Fig. 3. Pin configuration SOT764-1 (DHVQFN20) NXS0108 Q100 All information provided in this document is subject to legal disclaimers. Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 1 15 September 2020 2 / 25 OE 10 1 A1 GND 11 20 B1