LQR2V822MSEG Nichicon

S 30 ALUMINUM ELECTROLYTIC CAPACITORS Screw Terminal Type, 85C High speed charge-discharge QR series Suited for high frequency regenerative voltage for AC servomotor, general inverter. Suited for equipment used at valtage fluctuating area. QR Suited for rectifier circuit of voltage doubler Compliant to the RoHS directive (2011/65/EU). Hi speed charge- discharge NX Specifications Item Performance Characteristics Category Temperature Range 25 to +85C Rated Voltage Range 350 to 450V Rated Capacitance Range 680 to 15000 F Capacitance Tolerance 20% at 120Hz, 20C 3 CV After 5 minutes application of rated voltage, leakage current is not more than ( A) or 5 mA, whichever is smaller (at 20C). 3 CV Leakage Current C : Rated Capacitance(F), V : Voltage ( V ) 3 CV (Measurement frequency:120Hz at 20C) Tangent of loss angle (tan ) Rated voltage (V) 350 400 450 tan (MAX.) 0.15 0.15 0.15 Measurement frequency : 120Hz Rated voltage (V) 350 to 450 Stability at Low Temperature Z 25C / Z+20C Impedance ratio ZT/Z20(MAX.) 8 Capacitance change Within 20% of the initial capacitance value The specifications listed at right shall be met when the capacitors are restored Endurance to 20C after D.C. bias plus rated ripple current is applied for 5000 hours at tan 300% or less than the initial specified value 85C, the peak voltage shall not exceed the rated voltage. Leakage current Less than or equal to the initial specified value After storing the capacitors under no load at 85C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, Shelf Life they shall meet the specified value for endurance characteristics listed above. Capacitance change Within 20% of the initial capacitance value After an application of charge-discharge voltage for 20million times Endurance of charge- (charge-discharge voltage difference(V)=rated voltage 0.3, cycle tan 300% or less than the initial specified value 3Hz)capacitors shell meet the characteristics requirement listed at discharge behavior Leakage current Less than or equal to the initial specified value right Appearance There shell be found to remarkable abnormality on the capacitor Marking Printed with white color letter on darkbrown sleeve. Screw terminal types for 51 and larger 51 to 90 Screw terminal type Drawing Hexagenal headed bolt Bottom plate Sleeve 35 Screw terminal type Pressure relief vent Hexagenal headed bolt (M5) Bottom plate Sleeve Pressure relief vent 2 P h + B 7 2 A 1 H + MAX. 1 L 10 24 U 150.5 S 291 B +3MAX. 61 L 3-leg brackets for 90 capacitors have different hole shapes from the ordinary ones illustrated below. P Pressure relief vent 7 Dimension of terminal pitch (W) and length (R) and Nominal dia. of bolt (mm) Type numbering system (Example : 400V 1800 F) D W Nominal dia. of bolt R 1 2 3 4 5 6 7 8 9 10 11 12 13 14 51 22.0 6 3 M 5 L Q R 2 G 1 8 2 M S E F 63.5 28.6 6 3 M 5 Mounting bracket 76.2 31.8 6 3 M 5 (35) Code less 2-leg brackets 90 31.8 6 3 M 5 Case dia. code BN No brackets D Code Configuration (51 to 90) 35 C Dimension of mounting bracket Capacitance tolerance (20%) Code less 3-leg brackets (mm) 51 F BB 2-leg brackets Leg shape 63.5 G 3- -Leg 2 --Leg Rated Capacitance (1800F) No brackets BN 76.2 H D Symbol 51 63.5 76.2 90 51 63.5 76.2 90 Rated voltage (400V) 90 J 32.5 38.1 44.5 50.8 33.2 40.5 46.5 53 P Series name A 38.5 43 49.2 58.5 40 46.5 53 59 7.5 8.0 7.0 8.0 6.0 7.0 6.0 6.0 Type T S 5.0 5.0 5.0 5.0 4.5 4.5 4.5 4.5 Configuration 12 14 14 18 14 14 14 14 Cr (III) Plating U (RoHS compliant) 60 60 60 60 30 30 30 30 SE 20 25 30 35 25 35 35 35 H Please refer to page 328 for schematic of dimensions. h 15 20 24 25 15 20 20 20 Please contact to us if PVCless products are required. Dimension table in next page. CAT.8100D 120 T U 12.71 +2MAX. 35 3.5 10 451 5 1 W + 2 MAX. D T P 2 A 30ALUMINUM ELECTROLYTIC CAPACITORS QR series Dimensions 350V (2V) 400V (2G) Cap. Size Cap. Size Rated ripple Leakage Current Rated ripple Leakage Current tan Code tan Code (F) D L(mm) (mA) (F) D L(mm) (mA) (Arms) (Arms) 820 0.35 800 3.3 0.15 1.60 LQR2V821MSEC 680 0.35 800 03.2 0.15 1.56 LQR2G681MSEC 1000 0.35 100 4.3 0.15 1.77 LQR2V102MSEC 820 0.35 100 04.1 0.15 1.71 LQR2G821MSEC 1800 0.51 800 7.2 0.15 2.38 LQR2V182MSEF 1500 0.51 800 07.5 0.15 2.32 LQR2G152MSEF 2200 0.51 100 9.1 0.15 2.63 LQR2V222MSEF 1800 0.51 900 09.1 0.15 2.54 LQR2G182MSEF 0.51 110 10.8 0.15 2.91 LQR2V272MSEF 2200 0.51 110 10.4 0.15 2.81 LQR2G222MSEF 2700 63.5 800 10.6 0.15 2.91 LQR2V272MSEG 2700 63.5 900 11.5 0.15 3.11 LQR2G272MSEG 0.51 130 12.4 0.15 3.22 LQR2V332MSEF 0.51 150 13.7 0.15 3.44 LQR2G332MSEF 3300 3300 63.5 900 11.9 0.15 3.22 LQR2V332MSEG 63.5 110 13.2 0.15 3.44 LQR2G332MSEG 63.5 110 14.6 0.15 3.50 LQR2V392MSEG 63.5 130 16.0 0.15 3.74 LQR2G392MSEG 3900 3900 76.2 800 14.1 0.15 3.50 LQR2V392MSEH 76.2 900 15.3 0.15 3.74 LQR2G392MSEH 0.51 170 17.0 0.15 3.84 LQR2V472MSEF 63.5 150 18.7 0.15 4.11 LQR2G472MSEG 4700 4700 76.2 900 16.4 0.15 3.84 LQR2V472MSEH 76.2 110 18.3 0.15 4.11 LQR2G472MSEH 63.5 150 20.4 0.15 4.20 LQR2V562MSEG 63.5 170 22.0 0.15 4.49 LQR2G562MSEG 5600 5600 76.2 110 19.7 0.15 4.20 LQR2V562MSEH 76.2 130 21.4 0.15 4.49 LQR2G562MSEH 63.5 170 23.5 0.15 4.62 LQR2V682MSEG 6800 76.2 150 25.4 0.15 4.94 LQR2G682MSEH 6800 76.2 130 22.9 0.15 4.62 LQR2V682MSEH 76.2 170 28.6 0.15 5.00 LQR2G822MSEH 8200 0.90 100 22.5 0.15 4.62 LQR2V682MSEJ 0.90 130 27.8 0.15 5.00 LQR2G822MSEJ 63.5 190 27.1 0.15 5.00 LQR2V822MSEG 10000 0.90 150 32.7 0.15 5.00 LQR2G103MSEJ 8200 76.2 150 26.4 0.15 5.00 LQR2V822MSEH 12000 0.90 170 37.6 0.15 5.00 LQR2G123MSEJ 76.2 170 31.1 0.15 5.00 LQR2V103MSEH 15000 0.90 220 43.0 0.15 5.00 LQR2G153MSEJ 10000 0.90 130 30.2 0.15 5.00 LQR2V103MSEJ 12000 76.2 190 35.7 0.15 5.00 LQR2V123MSEH 15000 0.90 190 40.5 0.15 5.00 LQR2V153MSEJ 450V (2W) Cap. Size Rated ripple Leakage Current tan Code (F) D L(mm) (Arms) (mA) 3.5 0.15 1.65 680 0.35 100 LQR2W681MSEC 3.9 0.15 1.82 820 0.35 110 LQR2W821MSEC 5.2 0.15 2.20 1200 0.51 800 LQR2W122MSEF 6.3 0.15 2.46 1500 0.51 100 LQR2W152MSEF 7.4 0.15 2.70 0.51 110 LQR2W182MSEF 1800 7.9 0.15 2.70 63.5 800 LQR2W182MSEG 8.7 0.15 2.98 0.51 130 LQR2W222MSEF 2200 8.6 0.15 2.98 63.5 100 LQR2W222MSEG 10.2 0.15 3.30 0.51 150 LQR2W272MSEF 2700 10.0 0.15 3.30 76.2 800 LQR2W272MSEH 12.4 0.15 3.65 63.5 130 LQR2W332MSEG 3300 11.8 0.15 3.65 76.2 100 LQR2W332MSEH 13.7 0.15 3.97 63.5 150 LQR2W392MSEG 14.1 0.15 3.97 3900 76.2 110 LQR2W392MSEH 0.90 900 13.6 0.15 3.97 LQR2W392MSEJ 63.5 170 16.5 0.15 4.36 LQR2W472MSEG 76.2 130 16.3 0.15 4.36 4700 LQR2W472MSEH 0.90 110 15.8 0.15 4.36 LQR2W472MSEJ 63.5 190 19.4 0.15 4.76 LQR2W562MSEG 5600 0.90 130 19.1 0.15 4.76 LQR2W562MSEJ 76.2 170 23.3 0.15 5.00 6800 LQR2W682MSEH 0.90 150 26.1 0.15 5.00 8200 LQR2W822MSEJ 0.90 190 31.3 0.15 5.00 10000 LQR2W103MSEJ 0.90 220 35.5 0.15 5.00 12000 LQR2W123MSEJ Rated ripple current (Arms) at 85C 120Hz Frequency coefficient of rated ripple current Frequency (Hz) 50 60 120 360 1k 10k or more Coefficient 0.80 0.82 1.00 1.20 1.35 1.40 CAT.8100D