ALUMINUMELECTROLYTICCAPACITORS Chip Type, High Reliability High Temperature (260C) Reflow WH series Corresponding with 260C peak reflow soldering WH Recomended reflow condition : 260C peak 5 sec. 230C over 60 sec. 2 times (8 6.2, 10 10 : 1 time) Chip type high temperature range, for +125C use. High Applicable to automatic mounting machine fed with carrier tape. Temperature Compliant to the RoHS directive (2011/65/EU). Reflow UB Specifications Item Performance Characteristics Temperature Range Category 40 to +125C Rated Voltage Range 10 to 50V Rated Capacitance Range 10 to 330F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 1 minute s application of rated voltage, leakage current is not more than 0.03CV or 4(A) , whichever is greater. Measurement frequency : 120Hz at 20C Rated voltage (V) 10 16 25 35 50 Tangent of loss angle (tan ) tan (MAX.) 0.32 0.24 0.21 0.18 0.18 Measurement frequency : 120Hz Rated voltage (V) 10 16 25 35 50 Stability at Low Temperature Impedance ratio Z40C / Z+20C 12 8 6 4 4 ZT / Z20 (MAX.) Capacitance change Within 30% of the initial capacitance value The specifications listed at right shall be met when tan 300% or less than the intial specified value Endurance the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 125C. Leakage current Less than or equal to the initial specified value After storing the capacitors under no load at 125C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within 10% of the initial capacitance value Resistance to soldering maintained at 250C. The capacitors shall meet the characteristic tan Less than or equal to the initial specified value requirements listed at right when they are removed from the plate heat Leakage current Less than or equal to the initial specified value and restored to 20C. Marking Black print on the case top. Chip Type Type numbering system (Example : 10V 100 F) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 U W H 1 A 1 0 1 M C L 1 G S Positive (8 6.2) Plastic platform 0.3MAX. C0.2 Voltage (A:10V) Series Package code Configuration Capacitance tolerance (20%) Trade mark Rated capacitance (100F) Rated voltage (10V) L0.3 Negative Lot No. Capacitance H Series name Type (mm) Positive (8 10, 10 10) Plastic platform D L 8 6.2 8 10 10 10 0.3MAX. C0.2 A 3.3 2.9 3.2 Series Voltage (V:35V) B 8.3 8.3 10.3 C 8.3 8.3 10.3 E 2.3 3.1 4.5 Trade mark L 6.2 10 10 H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 L0.5 Negative Lot No. Capacitance H Voltage V 10 16 25 35 50 Code A C E V H Dimension table in next page. CAT.8100D A2 A2 100V 100A WH WH D0.5 D0.5 B0.2 B0.2 0.5MAX. 0.5MAX. E E A0.2 A0.2 A0.2 A0.2ALUMINUMELECTROLYTICCAPACITORS WH series Dimensions V 10 16 25 35 50 Cap.(F) Code 1A 1C 1E 1V 1H 10 24 100 8 6.2 22 38 220 8 6.2 33 46 330 8 6.2 44 8 10 47 58 470 8 6.2 48 8 10 52 10 10 100 101 8 6.2 58 8 10 66 8 10 74 10 10 80 220 221 8 10 90 10 10 102 10 10 116 Case size Rated D L (mm) ripple 330 331 10 10 112 Rated ripple current (mArms) at 125C 120Hz Frequency coefficient of rated ripple current Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more Coefficient 0.70 1.00 1.17 1.36 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D