ALUMINUMELECTROLYTICCAPACITORS Chip Type, High CV High Temperature (260C) Reflow WS series Corresponding with 260C peak reflow soldering Recomended reflow condition : 260C peak 5 sec. 230C over 60 sec. 2 times (8 6.2, 10 10 : 1 time) Chip type higher capacitance in large case size. WS Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). High Temperature Reflow UR Specifications Item Performance Characteristics Category Temperature Range 40 to +85C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 22 to 1500F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 1 minute s application of rated voltage, leakage current is not more than 0.03CV (A) . Measurement frequency : 120Hz at 20C Rated voltage (V) Tangent of loss angle (tan ) 6.3 10 16 25 35 50 tan (MAX.) 0.28 0.24 0.20 0.16 0.14 0.12 Measurement frequency: 120Hz Rated voltage (V) 6.3 10 16 25 35 50 Stability at Low Temperature Impedance ratio Z25C / Z+20C 5 4 3 2 2 2 ZT / Z20 (MAX.) Z40C / Z+20C 10 8 6 4 3 3 Capacitance change Within 20% of the initial capacitance value The specifications listed at right shall be met when tan 200% or less than the initial specified value Endurance the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 85C. Leakage current Less than or equal to the initial specified value After storing the capacitors under no load at 85C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Capacitance change Within 10% of the initial capacitance value Resistance to soldering which is maintained at 250C. The capacitors shall meet tan Less than or equal to the initial specified value the characteristic requirements listed at right when they heat Leakage current Less than or equal to the initial specified value are removed from the plate and restored to 20C. Marking Black print on the case top. Chip Type Type numbering system (Example : 10V 100 F) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 (6.3, 8 6.2) U W S 1 A 1 0 1 M C L 1 G S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Positive Plastic platform U W S 1 A 1 0 1 M C L 1 G S 0.3MAX. Voltage (A:10V) C0.2 Package code Series Positive Configuration Plastic platform Package code Capacitance tolerance (20%) Voltage (A:10V) 0.3MAX. C0.2 Series Configuration 1 Rated capacitance (100F) Trade mark Capacitance tolerance (20%) Rated voltage (10V) Rated capacitance (100F) 1 L0.3 Lot No. Capacitance Series name Trade mark Negative Rated voltage (10V) H 1 Size 8 6.2 only Type Series name L0.3 Capacitance Lot No. (mm) Negative Type DL H 1 Size 8 6.2 only 6.3 5.8 6.3 7.7 8 6.2 8 10 10 10 (mm) Positive A 2.4 2.4 3.3 2.9 3.2 Plastic platform DL B 6.3 5.86.6 6.3 7.76.6 8 6.28.3 8 108.3 10 1010.3 (8 10, 10 10) 0.3MAX. C0.2 Voltage (V:35V) Series C 6.6 6.6 8.3 8.3 10.3 A 2.4 2.4 3.3 2.9 3.2 Positive E 2.2 2.2 2.3 3.1 4.5 B 6.6 6.6 8.3 8.3 10.3 Plastic platform L 5.8 7.7 6.2 10 10 C 6.6 6.6 8.3 8.3 10.3 0.3MAX. C0.2 Voltage (V:35V) Series H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 E 2.2 2.2 2.3 3.1 4.5 Trade mark L 5.8 7.7 6.2 10 10 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Lot No. Capacitance L0.5 Trade mark Negative H Lot No. Capacitance L0.5 Negative H Voltage V 6.3 10 16 25 35 50 Code j A C E V H Dimension table in next page. CAT.8100D A2 A2 A2 A2 100A 100A 100V 100V WS WS WS WS D0.5 D0.5 D0.5 D0.5 B0.2 B0.2 B0.2 B0.2 0.5MAX. 0.5MAX. 0.5MAX. 0.5MAX. E E E E A0.2 A0.2A0.2 A0.2 A0.2 A0.2A0.2 A0.2ALUMINUMELECTROLYTICCAPACITORS WS series Dimensions V 6.3 10 16 25 35 50 Code Cap. (F) 0J 1A 1C 1E 1V 1H 22 6.3 5.8 045 220 33 6.3 5.8 055 8 6.2 095 330 47 6.3 5.8 065 8 6.2 105 8 10 140 470 100 6.3 5.8 070 8 6.2 125 8 6.2 145 8 10 175 10 10 195 101 150 6.3 5.8 085 6.3 7.7 151 8 10 192 8 10 214 10 10 238 151 220 8 6.2 160 8 6.2 175 8 10 215 10 10 250 10 10 265 10 10 289 221 330 8 6.2 190 8 10 240 8 10 270 10 10 305 10 10 324 331 470 8 10 265 8 10 290 10 10 330 10 10 393 471 680 8 10 318 10 10 374 10 10 396 681 Rated 1000 10 10 400 10 10 454 102 Case size D L (mm) ripple 1500 10 10 489 152 Rated ripple current (mArms) at 85C 120Hz Frequency coefficient of rated ripple current Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more Cap.(F) 00 Less than 47V 0.80 1.00 1.15 1.40 1.67 100 to 1500 0.85 1.00 1.08 1.20 1.30 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D