ARM-USB-OCD rev 1.00/07-2006 ARM-USB-OCD is unique device which combine JTAG debugging hardware, RS232 virtual port and power supply adapter in one single compact form. Many of the new laptop computers have no parallel nor serial ports but only USB, with ARM-USB-OCD you can debug your ARM boards, have full featured virtual RS232 port with all modem signals on it and the power jack can provide three fixed value voltages 5V 9V 12V DC via jumper selection. The base features are: - based on FT2232L IC from Future Technology Devices International Ltd. - fast speed USB 2.0 JTAG dongle interface, can be used with any ARM devices for programming and debugging (which are currently supported by openOCD). - the JTAG cable uses ARM s standard 2x10 pin JTAG connector - supports ARM targets working in voltage range 2.0 5.0 V DC - software supported by OpenOCD (open source) debugger - adds virtual RS232 port to your computer with all modem signals like: DTR, DSR, DCD, RTS, CTS, Rx, Tx - can be used as power supply to your target board with three jumper selectable power supplies: 5V 9V and 12VDC, USB source current is limited with resetable fuse at 300mA, at the different output voltage the maximum current is different: 5V/200mA, 9V/100mA, 12V/70mA, note that this also depend on your USB host current capabilities, if other USB devices are attached to your computer or if the laptop is running on batteries these figures may be different and depend on your computer USB host. - CD with Windows installer for full featured and open source tools as alternative to the commercial ARM development packages: GCC C compiler, openOCD debugger and Eclipse IDE. FT2232 signal assignments: JTAG signals VREF voltage follower input for the output buffers adjust JTAG signals as per your target board voltage levels ADBUS0 -> TCK ADBUS1 -> TDI ADBUS2 -> TDO ADBUS3 -> TMS ADBUS4 -> 0 to enable JTAG buffers ADBUS5 -> 0 if target present ADBUS6 -> TSRST in ADBUS7 -> RTCK ACBUS0 -> TRST ACBUS1 -> TSRST ACBUS2 -> TRST buffer enable ACBUS3 -> RED LED Power supply jumpers: RS232 signals BDBUS0 -> RS232 Tx BDBUS1 -> RS232 Rx BDBUS2 -> RS232 RTS BDBUS3 -> RS232 CTS BDBUS4 -> RS232 DTR BDBUS5 -> RS232 DSR BDBUS6 -> RS232 DCD the power supply jumpers are on right side of the 2x10 pin JTAG connector. - If both jumpers are open the output voltage is 12VDC - If right jumper is closed the output voltage is 9VDC - If left jumper is closed the output voltage is 5VDC Copyright 2006, OLIMEX Ltd. All right reserved. (this is the default setting) X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Hardware Debuggers category: Click to view products by Olimex manufacturer: Other Similar products are found below : CWH-CTP-VSPA-YE IJET-RISCV 410-251 1550 AC244028 AC244045 DV164045 AC244036 DB40 LPC DEBUG 2 ATATMEL-ICE ATATMEL-ICE-BASIC ATAVRONEKIT 76002055 IJET AC162051 AC162062 AC162064 AC162074 AC162078 AC162079 AC162087 AC162088 AC244024 AC244026 AC244027 AC244034 AC244035 AC244043 AC244044 AC244047 AC244048 AC244051 AC244054 AC320202 DV164131 DV164232 PG164100 ARM-USB-OCD-H ARM-USB-TINY-H 32115 ACC-DEBUG 114991786 8.07.10 8.08.28 8.18.00 8.19.00 8.19.28 8.20.00 AC244023