Electrode Holder PS- S(R)/-31 CSM PS- S(R) -31 DS E 7 3 Separate Electrode Holders for Water Supply and Drainage Control in Buildings. Small, Lightweight Electrode Holders for Use as Built-in Components. The PS- S(R) are separate Electrode Holders that allow the Electrodes to be withdrawn easily for inspection. The PS- S(R) come in 3, 4, or 5 pole models for supply and drainage of tap water in buildings. PS-31 is a small and light-weight Electrode Holder that is suitable for installation in limited space and built-in components. Refer to Safety Precautions for Electrodes and Electrode Holders. Ordering Information Electrode Holders Application Model General applications for purified water For 3-pole electrode PS-3S For 3-pole electrode (2-wire) PS-3SR For 4-pole electrode PS-4S For 4-pole electrode (2-wire) PS-4SR For 5-pole electrode PS-5S For 5-pole electrode (2-wire) PS-5SR PS-31 (SUS304, 300 mm) For small spaces (3-pole) PS-31 (SUS304, 1,000 mm) Accessories (Order Separately) Application Model Protective Cover (for PS- S and BF-3/-5) F03-11 Mounting Frame (for PS- S) F03-12 Mounting Frame for Installing in Concrete (for PS- S(R)) F03-13 Dust-proof Rubber Cap (for PS-31) F03-31 Specifications Item Model PS-3S(R) (See note 1.) PS-4S(R) (See note 1.) PS-5S(R) (See note 1.) PS-31 (See note 2.) No. of Electrodes 3 4 5 3 (See note 3.) Material Resin (PBT = Polybutylene terephthalate) Insulation resistance 100 M min. Operating temperature 10 to 70C (with no icing) Operating pressure Atmospheric pressure Applications Water supply and drainage control in buildings Limited Mounting Space Electrodes Purchase F03-01 separately. Single-piece construction Note: 1. The Two-wire Electrode Holders (R models) have a built-in resistor of 6.8 k. They should be used with the Two-wire 61F Controllers. 2. Cut the electrodes to the desired length. 3. PS-31 comes in a 3-pole model only. 1PS- S(R)/-31 PS- S(R) Electrode Holder Accessories (Order Separately) F03-11 Protective Cover F03-12 Spring Clamp F03-13 Mounting Frame for installing in concrete Used to clamp an Electrode Holder Firmly secure the F03-12 Spring Clamp to Use this Cover for PS-series Electrode with ease, as shown in the illustrations, the F03-13 Mounting Frame with M5 x 25 Holders with Mounting Frames (upper when the Electrode Holder is applied one in the following illustration), This screws and embed it into the concrete to a tank without a coupling. Cover can also be used when installing production water tank. Cut the F03-13 to Squeeze the mounting frame into the BF-series Electrode Holders match the depth of the concrete. the Holder as shown below. outdoors. This Cover is for protection from rain and wind. It is not waterproof. Applicable Electrode Holders: 115 dia. Applicable Electrode Holders: PS-3S(R), PS-4S(R), PS-5S 96 BF-3, BF-4, BF-5, PS-3S(R), PS-4S(R), PS-5S(R) 10 80 100 60 Weight: approx. 65g 96 70 Operating temp.: 10C to 70C 60 112 dia. Four, M5 x 25 mounting screws 72 dia. Weight: approx. 120g 120 dia. 82 dia. Protective Cover F03-11 Electrode Holder PS- S Mounting Frame Operating temp: 10C to 70C embedded into Electrode Electrode Weight: approx. 80g concrete Spring Clamp F03-12 Commonly used with Mounting Frame Note: If the F03-11 and F03-12 are used together, the screws and bolts that are provided with the F03-11 cannot be used. PS-31 Electrode Holder Accessories (Order Separately) F03-31 Dust-proof Rubber Bushing Note: This Bushing is not waterproof. 6 dia. (inner) 32 dia. 75 Material: Silicon rubber Accessories Required for Connecting the PS- S(R) and Electrodes (Order Separately) Electrodes Shorter Electrode Longer Separator (1-pole) than 1 m than 1 m The following items are required The following items are required for every for each pole. additional meter of electrode for each pole. Connecting nut Spring washer (See note 1.) 1 F03-01 Electrode 1 F03-01 Electrode Spring washer 1 F03-03 Lock Nut 1 F03-02 Connecting Nut Lock nut Lock nut 2 F03-03 Lock Nuts The Electrode can be cut Electrode Electrode anywhere based on the control Use F03-14 1P, 3P, and 5P Separators to level. prevent the electrodes from touching each another. Note: 1. The spring washer comes with the lock nut. 2. Refer to F03- for details on Electrodes, Connecting Nuts, Lock Nuts, and Separators. 2