ESD5384 ESD Protection Diode 5Line HDMI Control Line ESD Protection Functional Description The ESD5384 chip is a low capacitance ESD protection for HDMI wwwwww..onsemi.comonsemi.com 2 control pins. It also integrates pullup resistor for I C bus and pulldown resistor for hot plug detect and pullup resistor for CEC MARKINGMARKING line. DIAGRAMDIAGRAM The ESD protection circuitry prevents damage to the protected device when subjected to ESD surges up to 15 kV. The ESD5384 is available in 9 bump CSP package. WLCSP9WLCSP9 53M53M CASE 567CXCASE 567CX Features Line Capacitance: 12 pF max 5353 = Specific Device Code= Specific Device Code MM == Date Code Date Code IEC 6100042 Level 4 15 kV (air discharge) 8 kV (contact discharge) PINOUTPINOUT This is a PbFree Device 33 22 11 Applications AA SCLSCL CECCEC 5V5V HDMI Control Line Interfaces Smart Phones BB SDASDA GNDGND RPU2RPU2 Tablets Consumer Electronics CC HPDHPD GNDGND RPURPU (Bump(Bump Side) Side) ORDERINGORDERING INFORMA INFORMATIONTION SSeeee detailed ordering and shipping information in the package detailed ordering and shipping information in the package dimensionsdimensions section section on page 7 of this data sheet.on page 7 of this data sheet. A1 C3 B3 A3 A2 HPD SDA SCL CEC 1.75K 5V C1 1.75K B1 27K B2, C2 ESD5384 Figure 1. Electrical Schematic Semiconductor Components Industries, LLC, 2011 1 Publication Order Number: September, 2017 Rev. 1 ESD5384/D 100K ESD5384 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit V External pins (A1, A2, A3, B3 and C3): kV PP ESD IEC 6100042, level 4 air discharge 15 ESD IEC 6100042, level 4 contact discharge 8 Internal pins (B1, C1): ESD IEC 6100042, level 1 air discharge 2 ESD IEC 6100042, level 1 contact discharge 2 T Operating Temperature Range 30 to +85 C op T Storage Temperature Range 55 to +150 C stg Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. ELECTRICAL CHARACTERISTICS (Note 1) Symbol Test Condition Min Typ Max Unit V Breakdown Voltage (I = 1mA) 6 20 V BR r I Leakage Current V (V = 3 V per line), excluding HPD line 50 200 nA RM rm rm I Leakage Current V (V = 3 V per line), HPD line 32 A RM rm rm R1, R2 Resistance 1575 1750 1925 R3 Pullup Resistance 80 100 120 k R4 Pullup Resistance 22 27 32 k C pF V = 0 V, V = 30 mV, F = 1 MHz, A2 with B1 not connected 14 17 line line osc V = 0 V, V = 30 mV, F = 1 MHz, A3, B3 with C1 not connected. 24 29 line osc V = 0 V, V = 30 mV, F = 1 MHz, A2, A3, B3 with C1 and B1 grounded 10 12 line osc 1. All parameters specified at T = 25C unless otherwise noted. A TYPICAL CHARACTERISTICS Figure 2. Crosstalk Measurements www.onsemi.com 2