ESD Suppressor ESD Suppressor Type: EZAEG EZAEG1A, 2A, 3A Features Recommended Applications ESD protection of high-speed data lines High-Speed Data Lines Low capacitance (HDMI, Serial ATA, USB, IEEE1394, Display Port) (1608 size : 0.1 pF, 1005 size : 0.05 pF, Antenna Circuitry and RF Modules (Cellular Phones) 0603 size : 0.04 pF) Good ESD suppression characteristics Good ESD withstanding Explanation of Part Numbers 1 2 3 4 5 6 7 8 9 10 11 E Z A E G 2 A 5 0 A X Product Code Size Design Specification Peak Voltage Special Feature Packaging Methods Code Code Code Code Code Packaging Type ESD Suppressor Size (inches) Design Specification Peak Voltage Special Feature Pressed Carrier Taping 1 A 50 A 0603 (0201) Rated Voltage 30 V 500 V Standard C EZAEG1A 2mmPitch, 15000 pcs. 2 1005 (0402) Pressed Carrier Taping 3 X EZAEG2A 1608 (0603) 2mmPitch, 10000 pcs. Punched Carrier Taping V EZAEG3A 4mmPitch,5000pcs. Construction Dimensions in mm (not to scale) Protective coating L a Gap electrode Alumina substrate W t b Electrode (Between) Dimensions (mm) Type Mass (Weight) (inches) g/1000 pcs. LWa b t EZAEG1A 0.03 0.03 0.10 0.10 0.03 0.60 0.30 0.15 0.15 0.23 0.12 (0201) EZAEG2A 0.10 0.05 0.10 0.10 0.05 1.00 0.50 0.20 0.25 0.38 0.6 (0402) ESD absorbent material Electrode (Outer) EZAEG3A 0.15 0.15 0.20 0.20 0.10 1.60 0.80 0.30 0.30 0.50 2.2 (0603) Circuit Con guration Design and speci cations are each subject to change without notice. Ask factory for the current technical speci cations before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2009ESD Suppressor Ratings Type Clamping Category Temperature Range (1) (2) Capacitance Peak Voltage Rated Voltage (3) (Operating Temperature Range) (inches) Voltage +0.04 EZAEG1A (0201) 0.04 pF 0.03 500 V max. +0.05 EZAEG2A (0402) 0.05 pF 100 V max. 30 V max 55 to +125 C 0.04 (350 V typ.) +0.10 EZAEG3A (0603) 0.10 pF 0.08 (1) Capacitance = The capacitance value shall be measured under the conditions speci ed below. Frequency : 1 MHz10 %, Voltage : 1 Vrms0.2 Vrms, Temperature : 25 C2 C (2) Peak Voltage = The peak voltage value shall be measured under the following conditions. ESD test conditions : IEC61000-4-2, 8 kV contact discharge (3) Clamping Voltage = The clamping voltage value shall be measured at 30 ns after initiation of pulse and measured under the conditions speci ed below. ESD test conditions : IEC61000-4-2, 8 kV contact discharge Frequency Characteristics ESD Suppression Voltage Waveform 5 400 350 0 300 -5 250 -10 200 150 -15 100 -20 50 -25 0 -30 -50 110 100 1000 10000 -20 0 20 40 60 80 100 120 140 160 180 200 Times (nSecs) Frequency(MHz) Typical Circuits Requiring Protection HDMI circuit Antenna circuit Antenna HDMI Controller Ga/As-SW HDMI or Rx/Tx ASM Packaging Methods (Taping) Standard Quantity Type Kind of Taping Pitch (P1)Quantity EZAEG1A 15000 pcs./reel Pressed Carrier Taping 2 mm EZAEG2A 10000 pcs./reel EZAEG3A Punched Carrier Taping 4 mm 5000 pcs./reel Design and speci cations are each subject to change without notice. Ask factory for the current technical speci cations before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2009 Attenuation (dB) Volts (V)