PA5003.182NLT Pulse

SMT Power Inductors High Current Composite Inductor - PA5003.XXXNLT and PM2203.XXXNLT Height: 3.1mm Max Footprint: 5.7mm x 5.5mm Max Current Rating: up to 36Apk Inductance Range: 0.15uH to 4.7uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5003) and Automotive (PM2203) grades 4,5 Electrical Specifications 25C, Operating Temperature Range per Below 3 2 Part Number DC Resistance Inductance Rated Saturation K Factor 6 100KHz, 0.1V Current Current Commerical Automotive TYP. MAX. for Core Loss (-40C to 125C) (-55C to 155C) uH20% A m m A PA5003.151NLT PM2203.151NLT 0.15 22.2 2.1 2.31 36 458.5 PA5003.161NLT PM2203.161NLT 0.16 22.2 2.12 2.33 35 458.5 PA5003.331NLT PM2203.331NLT 0.33 19.2 3.2 3.52 28 291.7 PA5003.471NLT PM2203.471NLT 0.47 18.4 3.75 4.13 26 213.9 PA5003.561NLT PM2203.561NLT 0.56 17.7 4.05 4.52 22.2 213.9 PA5003.601NLT PM2203.601NLT 0.6 17.7 4.11 4.52 22 213.9 PA5003.801NLT PM2203.801NLT 0.8 13.1 5.14 5.65 20 168.9 PA5003.821NLT PM2203.821NLT 0.82 12.9 5.25 5.78 19.7 168.9 PA5003.102NLT PM2203.102NLT 1 12.2 6.9 7.6 16.5 139.5 PA5003.122NLT PM2203.122NLT 1.2 11 8.8 9.7 15 118.9 PA5003.152NLT PM2203.152NLT 1.5 10.5 10.1 11.2 14 103.5 PA5003.182NLT PM2203.182NLT 1.8 10.1 11.5 12.7 12.3 103.5 PA5003.222NLT PM2203.222NLT 2.2 9.7 13.2 14.5 10 91.7 PA5003.332NLT PM2203.332NLT 3.3 8.1 21 23.1 9.5 74.6 PA5003.472NLT PM2203.472NLT 4.7 5.9 33 36.3 8.2 58.3 Notes: 1. Actual temperature of the component during system operation (ambient plus case operating conditions. Circuit design, PCB trace size and thickness, airflow and temperature rise) must be within the standard operating range. other cooling provisions all affect the part temperature. Part temperature should be 2. The saturation current is the current at which the initial inductance drops ap- verified in the end application. proximately 30% at the stated ambient temperature. This current is determined by 5. Parts shown in bold are standard catalog parts and are available through sample placing the compnent in the specified ambient environment and applying a short stock and distribution. Parts in lighter font are available but are not necessarily held duration pulse current (to eliminate self-heating effect) to the component. in sample stock or distribution and lead times may be longer. Please contact Pulse 3. The rated current is the DC current required to raise the component temperature by for availablity. approximately 40C. Take note that the components performanc varies depending 6. The PM2203.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The on the system condition. It is suggested that the component be tested at the system mechanical dimensions are 100% tested in production but do not necessarily meet a level, to verify the temperature rise of the component during system operation. product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. 4. The part temperature (ambient+temp rise) should not exceed 125C under worst 1 power.pulseelectronics.com P808. C (04/19) 0 SMT Power Inductors High Current Composite Inductor - PA5003.XXXNLT and PM2203.XXXNLT Mechanical PA5003.XXXNLT and PM2203.XXXNLT D A C H E XXX 1R2 B F 16D/C02 FINAL LAYOUT SUGGESTED PAD LAYOUT Series A B C D E F L G H PA5003/PM2203 5.50.2 5.30.2 2.90.2 4.30.3 1.10.2 2.30.25 4.5 (REF) 2.0 (REF) 4.7 (REF) All Dimensions in mm. TAPE & REEL INFO Blank portions Chip cavity Blank portions K P1 200mm or more 400mm or more G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) TAPE SIZE (mm) QTY A G P W K PCS/REEL 1 0 PA5003/PM2203 330 16.4 8 16 2.3 2000 Typical Performance Curves PA5003.151NLT PA5003.161NLT 0.25 70 0.25 70 0.2 56 0.2 56 0.15 42 0.15 42 0.1 28 0.1 28 0.05 14 0.05 14 0 0 0 0 0 7 14 21 28 35 0 7 14 21 28 35 DC CURRENT(A) DC CURRENT(A) 2 power.pulseelectronics.com P808. C (04/19)