THT Power Inductors Toroid - Vertical, Low Profile and Klipmount Available in vertical, low profile and Klipmount SMPS averaging filter Characterized for general purpose use and ripple filters Single-layer designs 3 Can be used as differential mode inductors in EMI filters Electrical Specifications 25C - O perating Temperature -40C to 130C Reference Operating Values Design Control Values 6 5 1 4 Vertical Low Profile Inductance IDC ET Energy Inductance 20 kHz DCR Coil Klip* Lead OP Part Part Typical (AMPS) (V-Sec) Storage No DC (H) Test mV ( MAX) Size Mount Diameter Number Number (H) (J) (20%) No DC Code Package (in .003) PE-51591NL 20 2.0 52 40 32.8 33 .060 H .020 PE-92100NL 25 2.6 30 85 20.7 22 .043 A KM1 .020 PE-92101NL PE-92401NL 50 2.6 50 169 45.7 45 .071 B KM2 .020 PE-92102NL PE-92402NL 100 2.6 90 338 94.1 90 .100 C KM3 .020 PE-92103NL 35 2.6 55 118 28.4 36 .037 B KM2 .025 PE-92104NL PE-92404NL 70 3.0 85 315 61.0 73 .052 C KM3 .025 PE-92105NL PE-92405NL 145 3.0 140 653 141.8 140 .087 D KM4 .025 PE-92106NL 285 3.0 300 1283 264.1 340 .140 E KM5 .025 PE-92107NL 450 3.0 425 2025 436.3 500 .200 F .025 PE-92108NL PE-92408NL 67 3.6 130 648 90.7 110 .045 D KM4 .032 PE-92109NL 165 4.0 240 1320 152.0 260 .070 E KM5 .032 PE-92110NL 270 4.0 350 2160 263.9 400 .100 F .032 PE-92111NL 40 4.0 70 320 37.9 57 .027 C KM3 .032 PE-51590NL 22 5.0 44 275 20.3 37 .020 G .032 PE-92112NL PE-92412NL 100 5.0 200 1250 90.7 180 .034 E KM5 .042 PE-92113NL 170 5.0 300 2125 159.7 310 .050 F .042 PE-92114NL PE-92414NL 35.6 5.0 100 688 55.6 88 .023 D KM4 .042 PE-92115NL 95 7.0 225 2328 96.0 200 .025 F .051 PE-92116NL PE-92416NL 55 7.0 150 1348 49.1 100 .017 E KM5 .051 PE-92117NL 55 10.0 175 2750 55.9 120 .013 F .064 * Parts available with KlipMount option can be ordered by adding a K suffix to the part number (i.e. PE-92100K). 1 pulseelectronics.com P635.B (02/15)THT Power Inductors Toroid - Vertical, Low Profile and Klipmount Relationships Between Reference and Operating Conditions Inductance vs. Operating ET (at reference I ) DC Max. Operating ET vs. Frequency (at reference I ) DC 2.00 2.00 2.00 1.75 Temp. Rise 1.75 >40C 1.75 1.50 Temp. Rise 1.50 >40C 1.50 1.25 1.25 1.25 1.00 1.00 1.00 .75 .75 .75 .50 .50 .50 .25 .25 .25 0 .25 .50 .75 1.00 1.25 1.50 0 .25 .50 .75 1.00 1.25 1.50 OPERATING DC CURRENT 02030405060708090 100 REFERENCE I DC OPERATING ET OPERATING FREQUENCY kHz REFERENCE ET Mechanical Schematic Klipmount Package Base material meets flammability requirements of UL 94V-0 Mechanically rigid mount PC Board - automatic insertability 1 Lowest cost C A B C D H EV) Standard 2 Typical Package Maximum .130 .020 3,30,508 .340 .580 .650 .29 .110 KM-1 8,64 14,73 16,51 7,37 2,79 E D .450 .650 .700 .325 .150 2E KM-2 B 11,43 16,51 17,78 8,26 3,81 A .450 .850 .950 .415 .150 KM-3 11,43 21,59 24,13 10,54 3,81 .620 .970 1.10 .475 .225 KM-4 15,50 24,64 27,94 12,07 5,72 .700 1.30 1.40 .625 .250 KM-5 17,78 33,02 35,56 15,88 6,35 Note: Units with large wire sizes may exceed B dimension. KLIPMOUNT is a trademark of Pulse Engineering, Inc. Inches .010 Dimensions: Unless otherwise specified, all tolerances are mm 0,25 2 pulseelectronics.com P635.B (02/15) INDUCTANCE AT OPERATING I DC REFERENCE I DC INDUCTANCE AT OPERATING ET INDUCTANCE AT REFERENCE ET OPERATING ET FOR 40C TEMP. RISE REFERENCE ET