7W Class II AC-DC LED power supply Features Suitable for high brightness LED 250mA, 350mA, 500mA and 680mA constant AC/DC Converter Constant current operation Current 3.75kVAC isolation Fused input and SCP, OCP, OVP, OLP LED Driver RACD07 IP67 rated Description 7 Watt The RACD07 is a constant current 7W AC/DC source for LED lighting with a wide input voltage range. The LED drivers are available with constant current outputs of 250mA, 350mA, 500mA or 680mA. Constant The series is IP67 rated and suitable for use in dry, damp or wet areas. RACD07 drivers have a 3 year warranty. Current Single Output Selection Guide (1) Part Input Constant Current Efficiency Rated Power Number Voltage Range Mode min. max. VAC VDC mA % W RACD07-250 90-295 14-28 250 75 7 RACD07-350 90-295 10-20 350 70 7.3 RACD07-500 90-295 5-14.5 500 70 7.2 RACD07-700 90-295 3-10.5 680 70 7.1 All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Notes: Note1: Constant current operation region is within 75%-100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. Model Numbering E340696 RACD07- UL8750 certified nom. Output Power nom. Output Current UL1310 certified CSA-C22.2 No. 223-M91 certified CSA-C22.2 No. 250.13-12 certified Specifications (measured ta= 25C and 115/230VAC) IEC/EN61347 certified IEC/EN61347-2-13 certified BASIC CHARACTERISTICS EN55015 compliant Parameter Condition Min. Typ. Max. EN61547 compliant EAC 90VAC 230VAC 295VAC Input Voltage Range 120VDC 415VDC Input Current full load, 100VAC 200mA Inrush Current 230VAC 10A No Load Power Consumption 230VAC 0.5W Input Frequency Range 47Hz 63Hz Power Factor 0.50 Start-up Time 1s Hold-up Time 18ms Set-up Time full load, 230VAC 0.5s Internal Operating Frequency 45kHz (2) Output Ripple Current 20MHz BW 30mAp-p Notes: Note2: Measured with a 12 twisted pair-wire terminated with 0.1F & 47F parallel capacitor continued on next page www.recom-power.com REV.: 4/2019 L-1RACD07 AC/DC Converter Series Specifications (measured ta= 25C and 115/230VAC) Input Voltage vs. Load 100 90 80 70 60 50 40 30 20 10 0 80 90100 120 140 160 180 200 220 240 295 Input Voltage VAC REGULATIONS Parameter Condition Value Output Voltage Accuracy includes: line, load and tolerance 5% Output Current Accuracy 3% typ. / 7% max. PROTECTION Parameter Condition Value Internal Input Fuse T1A, slow blow Short Circuit Protection (SCP) Hiccup Mode, auto recovery after fault condition is removed Overload Protection (OLP) 105% - 120% typ. Over Current Protection (OCP) Constant current mode protection Isolation Voltage I/P to O/P 3.75kVAC / 1 minute Isolation Resistance 500VDC 100MW min. Notes: Note3: Refer to local wiring regulations if input over-current protection is also required Maximum loading of automatic circuit breakers* * 115VAC, 1Ohm, 90 phase angle * 230VAC, 1Ohm, 90 phase angle * 277VAC, 1Ohm, 90 phase angle and max. load and max. load and max. load Circuit Breaker Circuit Breaker Current Circuit Breaker Circuit Breaker Current Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A Typ 10A 16A 20A 25A Typ 10A 16A 20A 25A C 101 128 171 228 B 61 100 121 150 B 70 115 139 172 C 121 164 221 291 C 139 188 254 334 ENVIRONMENTAL Parameter Condition Value Operating Temperature Range natural convection 0.1m/s, full load -20C to +50C Max. Case Temperature +85C Operating Humidity non condensing 20% - 90% RH IP Rating IP67 Vibration 10-500Hz, 2G 10 minute/cycle 1 cycle period for 60 min each along X, Y and Z axes 3 Design Lifetime +25C ambient 70 x 10 hours MTBF according to MIL-HDBK-217F, G.B. +25C 200 x 10 hours continued on next page www.recom-power.com REV.: 4/2019 L-2 Output Load %