RP08-1215DA Recom Power

C C S S O O R R w E E M M T T P P R R a L L R I I E E A A r V V N N A N N T T r 2:1 input voltage range Features 1.6kVDC isolation DC/DC Converter UL60950-1 certified Efficiency up to 87% Regulated Low profile, 10.2mm height Converter Over current protection RP08-A Description 8 Watt 3 The RP08-A series DC/DC converters are certified to UL60950-1 and cUL60950-1. This makes them DIP24/SMD ideal for all telecom and industrial applications where approved safety standards are required. The DIP24 package is available in both pinned and SMD case styles and meets military standards for ther- Single and Dual mal shock and vibration tolerance. Output Selection Guide (1) (1) Part Number Input Output Output Input Efficiency Max. Capacitive (2) Voltage Range Voltage Current Current typ. Load VDC VDC mA mA % F (3) RP08-123.3SA 9-18 3.3 2000 688 80 3300 (3) RP08-1205SA 9-18 5 1500 753 83 1600 (3) RP08-1212SA 9-18 12 666 757 88 350 (3) RP08-1215SA 9-18 15 533 766 87 240 (3) RP08-243.3SA 18-36 3.3 2000 344 80 3300 (3) RP08-2405SA 18-36 5 1500 377 83 1600 (3) RP08-2412SA 18-36 12 666 387 86 350 (3) RP08-2415SA 18-36 15 533 392 85 240 (3) RP08-483.3SA 36-75 3.3 2000 172 80 3300 (3) RP08-4805SA 36-75 5 1500 188 83 1600 (3) RP08-4812SA 36-75 12 666 194 86 350 (3) RP08-4815SA 36-75 15 533 194 86 240 (3) RP08-1205DA 9-18 5 800 803 83 1000 (3) RP08-1212DA 9-18 12 333 766 87 160 (3) RP08-1215DA 9-18 15 267 785 85 100 22++ RoHSRoHS REACHREACH compliantcompliant (3) compliantcompliant 10 from 1010 from 10 RP08-2405DA 18-36 5 800 407 82 1000 E196683 (3) RP08-2412DA 18-36 12 333 387 86 160 (3) RP08-2415DA 18-36 15 267 393 85 100 (3) RP08-4805DA 36-75 5 800 196 85 1000 (3) RP08-4812DA 36-75 12 333 191 87 160 (3) RP08-4815DA 36-75 15 267 192 87 100 Notes: UL60950-1 certified EN55032 compliant Note1: Maximum values at nominal input voltage and full load Note2: Max. Cap load is tested at minimum Input and constant resistive load Model Numbering RP08- A/ (3) nom. Input Voltage Package nom. Output Voltage Single or Dual Notes: Note3: no suffix for standard DIP24 package add suffix /SMD for SMD package Ordering Examples RP08-4805SA/SMD = 48V Input, 5V Output, Single, SMD Package RP08-1205DA = 12V Input, 5V Output, Dual, DIP24 Package www.recom-power.com REV.: 4/2020 PD-1 O O P P E a C C R R O O Y M M n D D O O U U t C C C C E E y T T R R S SRP08-A DC/DC Converter Series Specifications (measured Ta= 25C, nom. Vin, full load and after warm-up unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Internal Input Filter Pi-Type nom. Vin = 12VDC 9VDVC 12VDC 18VDC Input Voltage Range nom. Vin = 24VDC 18VDC 24VDC 36VDC nom. Vin = 48VDC 36VDC 48VDC 75VDC nom. Vin = 12VDC 36VDC Input Surge Voltage 100ms max. nom. Vin = 24VDC 50VDC nom. Vin = 48VDC 100VDC (4) Minimum Load 10% Power up 700ms Start-up Time ON/OFF CTRL 5ms Operating Frequency Range 270kHz 300kHz 330kHz (5) ON/OFF CTRL DC-DC ON Open or 3.0VDC < V < 12VDC CTRL Positive Logic refer to ON/OFF CTRL DC-DC OFF Short or 0VDC < V < 1.2VDC CTRL Input Current of CTRL pin drive current I -0.5mA +0.5mA CTRL Standby Current DC-DC OFF I 2.5mA In 20MHz BW 50mVp-p Output Ripple and Noise Input Reflected Ripple Current 20mAp-p Notes: Note4: The RP08 series requires a minimum of 10% loading on the output to maintain specified regulation Operation under no-load condition will not damage these devices, however they may not meet all listed specification Note5: The pin voltage is referenced to -Vin pin RP08-1205SA Efficiency vs. Output Current Efficiency vs. Input Voltage 95 90 90 85 85 80 80 75 70 75 65 60 70 55 9Vin 50 65 12Vin 45 18Vin 60 40 9 10 11 12 13 14 15 16 17 18 10 20 30 40 50 60 70 80 90 100 Input Voltage VDC Output Current % continued on next page www.recom-power.com REV.: 4/2020 PD-2 Efficiency % Efficiency %