RL1N4001 THRU RL1N4007 SILICON RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 1.0 Ampere FEATURES *High reliability * Low leakage current Low forward voltage drop * *High current capability A-405 MECHANICAL DATA * Case : Molded plastic ( ) .025 0.6 DIA. * Epoxy : Device has UL flammability classification 94V-0 .021 (0.5) 1.0 (25.4) * Lead : MIL-STD-202E method 208C guaranteed MIN. * Mounting position : Any * Weight : 0.20 gram ( ) .205 5.2 .166 (4.2) .107 (2.7) DIA080 (2.0) 1.0 (25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) O MAXIMUM RATINGS ( TA=25 C unless otherwise noted) RL1N4001 RL1N4002 RL1N4003 RL1N4004 RL1N4005 RL1N4006 RL1N4007 RATINGS SYMBOL UNITS Maximum Recurrent Peak Reverse Voltage V 50 100 200 400 600 800 1000 Volts RRM Maximum RMS Voltage V 35 70 140 280 420 560 700 Volts RMS V 50 100 200 400 600 Volts Maximum DC Blocking Voltage DC 800 1000 Maximum Average Forward Rectified Current o I 1.0 Amps O at TA=55 C Peak Forward Surge Current 8.3 ms single half sine-wave I 30 Amps FSM superimposed on rated load (JEDEC method) 2 2 Typical Current Squarad Time I t A /Sec 3.74 0 Typical Thermal Resistance R 50 C/W Q JA Typical Junction Capacitance (Note 1) C 15 pF J 0 Operating and StorageTemperature Range TJ,TSTG -55 to + 150 C O ELECTRICAL CHARACTERISTICS ( TA=25 C unless otherwise noted) CHARACTERISTICS SYMBOL RL1N4001 RL1N4002 RL1N4003 RL1N4004 RL1N4005 RL1N4006 RL1N4007 UNITS Maximum Instantaneous Forward Voltage at 1.0A DC V 1.0 Volts F o T = 25 C 1.0 Maximum DC Reverse Current A o at Rated DC Blocking Voltage T = 100 C 50 A I R M A Maximum Full Load Reverse Current Average, Full 30 O Cycle .375 (9.5mm) lead length at T =75 C L 2016-09 NOTES : 1. Measured at 1 MHz and applied reverse voltage of 4.0 volts. REV: A 2.Fully ROHS complian100% Sn plating (Pb-free. 3. Available in Halogen-free epoxy by adding suffix -HF after the part nbr.RATING AND CHARACTERISTICS CURVES ( RL1N4001 THRU RL1N4007 ) 1000 2.0 M 100 1.5 O 10 T = 100 C J 1.0 1.0 0.5 Single Phase Half Wave 60Hz 0.1 Resistive or Inductive Load O T = 25 C J 0 0.01 0 25 50 75 100 125 150 175 0 20 40 60 80 100 120 140 O AMBIENT TEMPERATURE, ( C) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.1 TYPICAL FORWARD CURRENT FIG.2 TYPICAL REVERSE DERATING CURVE CHARACTERISTICS 20 40 10 O T = 25 C J 20 4 2 1.0 10 8 6 .4 .2 4 T = 25 J .1 Pulse Width=300uS 1% Duty Cycle 2 .04 .02 1 .01 0.1 0.4 1.0 4 10 40 80 .6 .8 1.0 1.2 1.4 1.5 INSTANTANEOUS FORWARD VOLTAGE, (V) REVERSE VOLTAGE, (V) FIG.3 TYYPICAL INSTANTANEOUS FORWARD FIG.4 TYPICAL JUNCTION CAPACITANCE CHARACTERISTICS 30 8.3mS Single Half Sine-Wave JEDEC Method 25 20 15 10 0 1 2 4 6 8 10 20 40 80 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIIVE FORWARD SURGE CURRENT INSTANTANEOUS REVERSE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, ( A) JUNCTION CAPACITANCE, (pF)