LTR10EVHFLR160 ROHM

High power thick film shunt resistors<wide terminal type> LTR seriesLHR series (low TCR) Datasheet Features 1)Chip Resistors for current detection : 10m ~ 2)High joint reliability with long side terminations. 3)Improvement of rated power enables to displace smaller size of resistors,and it contributes space savings in your set. 4)ROHM resistors have obtained ISO9001 / IATF16949 certification. 5)Corresponds to AEC-Q200. Products list Rated Operating Size Temperature Automotive power Resistance range temperature Resistance Part No. coefficient grade (70) range tolerance available (mm) (inch) (W) (ppm / ) () () 0125 0.033R0.043 (E24 series) F ( 1% ) (E24 series) Yes LHR18 1632 0612 1.25 0100 0.043R0.3 -55 +155 J ( 5% ) (E24 series) 075 0.3R1 F ( 1% ) LTR10 1220 0508 0.5 150 0.047R10 (E24 series) -55 +155 Yes J ( 5% ) (E24 series) 0300 0.01R0.02 (E24 series) F ( 1% ) 0200 0.02R0.05 LTR18 1632 0612 1.0 -55 +155 Yes J ( 5% ) (E24 series) 0150 0.05R0.5 (E24 series) 100 0.5R1 (E24 series) 0300 0.01R0.02 0200 0.02R0.051 (E24 series) F ( 1% ) LTR50 2550 1020 2.0 -55 +155 Yes J ( 5% ) 0150 0.051R0.1 (E24 series) (E24 series) 100 0.1R0.91 F ( 1% ) (E24 series) 0+150 0.1R0.2 F ( 1% ) (E24 series) Yes 2.0 0+100 0.2R1 -55 +155 J ( 5% ) (E24 series) 200 0.1R1 LTR100 3264 1225 (E24 series) 0300 0.01R0.02 F ( 1% ) (E24 series) Yes 3.0 0200 0.02R0.051 -55 +155 J ( 5% ) 0150 0.051R0.1 (E24 series) *Design and specifications are subject to change without notice. Under Development Carefully check the specification sheet supplied with the product before using or ordering it. Part number description L T R 1 0 E V H J L 1 R 0 Resistance Special Part No. Size (mm inch ) Packaging specifications code Nominal resistance tolerance part code Resistance code, 3 or 4 digits. 10(1220 0508 ) Packaging Quantity Part No. Code F (1%) LTR U 10m specifications / Reel 18(1632 0612 ) (High power Resistance J (5%) S 11m 50(2550 1020 ) tolerance Resistance thick film shunt Paper tape 91m LHR18 EZP 5,000 + code resistors wide 100(3264 1225 ) (4mm Pitch) L 100m Special code terminal type) Paper tape LTR10 EVH 5,000 (4mm Pitch) FU, FS 4 digits FL, JS Paper tape LHR LTR18 EZP 5,000 (High power 3 digits JU, JL (4mm Pitch) thick film shunt Embossed resistors wide tape LTR50 UZP 5,000 terminal type /Low TCR) (4mm Pitch) Embossed tape LTR100 JZP 4,000 (4mm Pitch) www.rohm.com 1/4 2020 ROHM Co., Ltd. All rights reserved. 2020.07 - Rev.KLTR series LHR series (low TCR) -low ohmic- Datasheet Chip resistor dimensions and markings LHR18 LTR10 LTR18/100 LTR50 <Marking method> There are four digits used for the calculation number according to IEC code.L means decimal point of m unit in case resistance value is 0.01 or less.R means decimal point of unit in case resistance value is above 0.01 . Example : 4digits10m=10L0, 100m=R100 3digits100m=R10, 1=1R0 (Unit:mm) Marking Part No. (mm) (inch) L W t a b existence LHR18 1632 0612 1.60.10 3.20.10 0.580.10 0.300.20 0.500.20 Yes LTR10 1220 0508 1.20.10 2.00.10 0.550.10 0.300.20 0.350.20 Yes LTR18 1632 0612 1.60.10 3.20.10 0.580.10 0.500.20 0.500.20 No LTR50 2550 1020 2.50.15 5.00.15 0.580.15 0.380.20 0.900.20 Yes LTR100 3264 1225 3.20.15 6.40.15 0.550.15 0.400.25 1.130.25 No Land pattern example (Unit:mm) Dimensions A B C D Part No. LTR10 0.50 1.98 2.20 0.74 LTR18 0.55 2.90 3.20 1.18 LHR18 LTR50 0.80 3.35 5.00 1.28 LTR100 0.83 3.69 6.40 1.43 www.rohm.com 2/4 2020 ROHM Co., Ltd. All rights reserved. 2020.07 - Rev.K