REVISION S FJ-XX-X-XX-X STRIP LENGTH No OF POSITIONS -2: .079 2.00 -05, -10, -15, -20, -25, -30 *-4: .157 4.00 -6: .236 6.00 DO NOT C3 STYLE SCALE FROM **-S: SINGLE ENDED LENGTH LENGTH (SPECIFY IN -XX INCHES .125 3.18 THIS PRINT -D: DOUBLE ENDED -XX:X INCHES .125 3.18 INCH -R: REVERSE STIFFENER (-S STYLE 2.500 63.50 MIN) (-D & -R STYLE 2.000 50.80 MIN) .03 0.7 REF FC-XX-1.0 * = RECOMMENDED MATING WITH FC1 ** = AS OF 1/1/11, -S (SINGLE ENDED) ONLY AVAILABLE TO EXISTING CUSTOMERS, ALL OTHERS WILL BE ASP s. 2 MAX SWAY (TYP) (No. OF POS. -1) x .03937 C1 (No. OF POS x .03937 1.0000 ) 1.000 +.03937 1.0000 .010 .25 No. OF POS x .03937 1.0000 (SEE NOTE 3) + .03937 1.0000 .005 .13 (SEE NOTE 2) .005 0.13 (TYP) .015 .38 (SEE TABLE 1) .0256.008 0.6500.20 C6 (TO BE MEASURED AT SECTION BASE OF EXPOSED LEAD) S .01 0.3 REF .004 0.10 REF C2 .207 5.26 REF FIG 1 .012.002 0.300.05 .021 0.52 REF HAND BUILT (SEE NOTE 6) S -S: SINGLE ENDED (FJ-10-S-XX-2 SHOWN) FS-20 .003 0.08 REF .01 0.2 REF .030 .76 (SEE TABLE 1) .0155 0.393 REF FIG 4 MACHINE BUILT (SEE NOTE 6) .100 2.54 -S: SINGLE ENDED REF (FJ-10-S-XX-2 SHOWN) SAME AS FIG 1 EXCEPT WHERE SHOWN UNLESS OTHERWISE SPECIFIED, PROPRIETARY NOTE DIMENSIONS ARE IN INCHES. THIS DOCUMENT CONTAINS INFORMATION NOTES: CONFIDENTIAL AND PROPRIETARY TO TOLERANCES ARE: 1. REPRESENTS A CRITICAL DIMENSION. SAMTEC, INC. AND SHALL NOT BE REPRODUCED DECIMALS ANGLES OR TRANSFERRED TO OTHER DOCUMENTS OR 2. MEASURE WHERE STIFFENER AND CABLE ARE ATTACHED. DISCLOSED TO OTHERS OR USED FOR ANY .XX: .01 .25 2 520 PARK EAST BLVD, NEW ALBANY, IN 47150 3. MEASURED ALONG LENGTH OF CABLE, EXCEPT WHERE STIFFENER PURPOSE OTHER THAN THAT WHICH IT WAS .XXX: .005 .13 PHONE: 812-944-6733 FAX: 812-948-5047 OBTAINED WITHOUT THE EXPRESSED WRITTEN IS ATTACHED TO CABLEXXXX: .0020 .050 CONSENT OF SAMTEC, INC. e-Mail: info SAMTEC.com code: 55322 4. NOTE DELETED. DESCRIPTION: DO NOT SCALE DRAWING SHEET SCALE: 4:1 5. STIFFENER IS TRIMMED TO CORRECT WIDTH. MATERIAL: .03937 1.0000 FLEX CABLE JUMPER CONDUCTORS: TIN PLATED COPPER 6. HAND BUILT PARTS USE A BLUE STIFFENER., MACHINE BUILT PARTS SURFACE FINISH EITHER BRIGHT ACID TIN (99.9% SN) DWG. NO. USE A BLACK STIFFENER. OR MATTE TIN (95.5% SN, 3.5% AG, 1% CU) FJ-XX-X-XX-X INSULATION: POLYESTER STIFFENER: POLYESTER BY: KEVIN B 3/29/99 SHEET OF1 2 F: DWG MISC MKTG FJ-XX-X-XX-X-MKT.SLDDRWREVISION S FC-XX-1.0 LENGTH (SPECIFY IN -XX INCHES .125 3.18 ) .015 .38 .015 .38 (SEE TABLE 1) (SEE TABLE 1) FOR -S: X LENGTH + .591 15.16 ) .050 1.27 FOR -D & -R: X LENGTH + 1.181 30.00 ) .050 1.27 FS-20 IN-PROCESS 1 SEE NOTE 5 FIG. 2 -D: DOUBLE ENDED (SAME AS FIG. 1, UNLESS STATED) LENGTH .43 11.0 (SPECIFY IN -XX INCHES .125 3.18 .015 .38 FS-20 (SEE TABLE 1) FC-XX-1.0 C4 .015 .38 1.0225.0075 25.9700.191 (SEE TABLE 1) FS-20 .413.030 10.490.76 FIG 3 -R: REVERSE STIFFENER (SAME AS FIG 1, UNLESS STATED) C5 .207.005 5.250.13 FS-20 .787 20.00 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY 520 PARK EAST BLVD, NEW ALBANY, IN 47150 IN-PROCESS 2 PURPOSE OTHER THAN THAT WHICH IT WAS PHONE: 812-944-6733 FAX: 812-948-5047 OBTAINED WITHOUT THE EXPRESSED WRITTEN (TYP ON BOTH ENDS FOR -D & -R STYLES) e-Mail: info SAMTEC.com code: 55322 CONSENT OF SAMTEC, INC. DESCRIPTION: DO NOT SCALE DRAWING .03937 1.0000 FLEX CABLE JUMPER DWG. NO. SHEET SCALE: 3:1 FJ-XX-X-XX-X F: DWG MISC MKTG FJ-XX-X-XX-X-MKT.SLDDRW BY: KEVIN B 3/29/99 SHEET OF2 2