NOTES: TFM-1XX-XX-XXX-D-XXX REVISION FD C 1. REPRESENTS A CRITICAL DIMENSION. OPTION 2. MINIMUM PUSHOUT FORCE FOR CONTACTS, WELD TABS, No OF POSITIONS -A: ALIGNMENT PIN (USE TFM-XX-D-XX-A, AND THREADED INSERTS: 12 OZ. LEAD STYLE -01, -02, -03: -02 THRU -50 (ALL SEE TABLE 1) (SEE FIG 8, SHT 3) 3. MINIMUM LOCKING CLIP RETENTION: 8 OZS. DO NOT POSITIONS AVAILABLE) (NOT AVAILABLE FOR -RA OR -REX) 4. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005 0.13 SCALE FROM -LC: LOCKING CLIP (USE LC-05-TM) LEAD STYLES -11, -12, -13: (-05 THRU -50 MULTIPLES OF 5) 5. MAXIMUM TERMINAL BURR: .003 0.08 THIS PRINT POSITIONS 12, 16, 17 ALSO AVAILABLE (NOT AVAILABLE FOR -RA OR -REX) 6. COPLANARITY: .004 0.10 = POS 02 THRU 26 C LEAD STYLES -21, 22, 23: (-05 THRU -50 MULTIPLES OF 5) (SEE FIG 10, SHT 3 & NOTES 3 & 11) .006 0.15 = POS 27 THRU 50 POSITIONS 12 & 13 ALSO AVAILABLE -P: PICK AND PLACE PAD (USE PPP-04) 7. MEASURED FROM BEND. LEAD STYLES 31, 32: 12 POSITION ALSO AVAILABLE (AVAILABLE IN ALL POSITIONS -05 THRU 8. DIMENSION CHANGED PER REVISION AD. CONTACT ENGINEERING -50 EXCEPT -05 WITH -WT) FOR INFORMATION. (NOT AVAILABLE FOR -RA OR -REX, 9. MEASURE FROM TIPS OF PIN. LEAD STYLE SEE FIG 7, SHT 3) 10. THIS FEATURE ONLY PRESENT ON -01 &-02 LEAD STYLES. -RA: RIGHT ANGLE THROUGH HOLE SURFACE MOUNT 11. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, (AVAILABLE ONLY IN LEAD STYLE: -01 -01, -03 (SEE FIG 1) -02 (SEE FIG 2) THE LC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC SEE FIG 5, SHT 2) -11, -13 (SEE FIG 1) -12 (SEE FIG 2) RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -TR: TAPE AND REEL (SEE FIG 4, SHT 7) -21,-23 (SEE FIG 1) -22 (SEE FIG 2) LC OPTION. (NOT AVAILABLE WITH -DS OPTION -31 (SEE FIG 1) -32 (SEE FIG 2) 12. SIDES OF PLASTIC BODIES ON ALL LEAD STYLES EXCEPT THE -01, -02 & -03 OR THROUGH HOLE LEAD STYLE) WILL BE SOLID AND WITHOUT SIDE SLOTS. PLATING SPECIFICATION -SA: STAKED ALIGNMENT PIN (SEE FIG 9, SHT 3) 13. NOTE DELETED. -S: 30 SELECTIVE GOLD ON CONTACT AREA, (NOT AVAILABLE FOR -RA OR -RE) MATTE TIN TAIL -K: POLYIMIDE FILM (SEE FIG 3, SHT 2) -L: 15 SELECTIVE GOLD ON CONTACT AREA, (USE K-DOT-.217-.313-.005) (No OF POSITIONS x .050 1.27 ) + .125 3.18 REF MATTE TIN TAIL (NOT AVAILABLE FOR -RA OR -REX) -F: 3 FLASH GOLD ON CONTACT AREA, (ALL LEAD STYLES EXCEPT -21 AVAILABLE) (No OF POSITIONS x .050 1.27 ) + .025 .64 REF MATTE TIN TAIL -WT: WELD TABS (USE WT-25-XX-T) -H: 30 SELECTIVE GOLD ON CONTACT AREA, (AVAILABLE ON -01, -02 & -03 LEAD .110 2.79 REF 3 FLASH GOLD ON TAIL 02 STYLES ONLY) (SEE FIG 6, SHT 2) -SM: 30 SELECTIVE GOLD ON CONTACT AREA, (MATES WITH SFSS/SFSD -SR & -DR ONLY) MATTE TIN TAIL (NOT AVAILABLE WITH -A, -LC, .155 3.94 -LM: 15 SELECTIVE GOLD ON CONTACT AREA, -RA, OR -SA OPTIONS) MATTE TIN TAIL REF -RE1: RIGHT ANGLE ELEVATED .062 PCB -FM: 3 FLASH GOLD ON CONTACT AREA, (USE TFM-XX-D-01-RE, NOT AVAILABLE MATTE TIN TAIL WITHOUT -WT, AVAILABLE IN LEAD -STL: 30 SELECTIVE GOLD ON CONTACT AREA, 01 STYLE -01 ONLY, -03 THRU -50 POS) TIN/LEAD (90/10 5%) TAIL .050 1.27 .225 5.72 (MATES WITH SFSS/SFSD -SR & -DR ONLY) .075 1.91 (SEE FIG 11, SHT 4) REF REF REF BODY SPECIFICATION -RE2: RIGHT ANGLE ELEVATED .093 PCB SEE NOTE 10 -D: DOUBLE ROW (USE TFM-XX-D-01-RE, NOT AVAILABLE WITHOUT -WT, AVAILABLE IN LEAD C .050 1.27 STYLE -01 ONLY, -03 THRU -50 POS) (No OF POSITIONS x .050 1.27 ) - .050 1.27 (MATES WITH SFSS/SFSD -SR & -DR ONLY) 2 MAX SWAY (SEE FIG 11, SHEET 4) (EITHER DIRECTION) -SN: SOLDER NAIL FOR .062 BOARD .018 0.46 REF REF .135 3.43 REF (TFM-XX-D-01-SN AND WT-27-01-T) 2 MAX SWAY (SEE TABLE 1, (SEE FIG12, SHT 3) (EITHER DIRECTION) (ONLY AVAILABLE WITH -02 LEAD STYLE) SHT 7) (NOT AVAILABLE WITH OPTIONS -A, -LC, .096 2.44 -RA, -SA, -WT, -RE1 OR -RE2) .1635 4.153 REF (SEE NOTE 8) -SN2: SOLDER NAIL FOR .093 BOARD REF (SEE TABLE 1, (TFM-XX-D-01-SN AND WT-27-02-T) SHT 7) (SEE FIG12, SHT 3) (ONLY AVAILABLE WITH -02 LEAD STYLE) (NOT AVAILABLE WITH OPTIONS -A, -LC, SEE NOTE 12 -RA, -SA, -WT, -RE1 OR -RE2) -DS: DUAL SCREW DOWN FOR .062 BOARD .010 0.25 REF .014 0.36 REF (SEE FIG 18, SHT 5) (ONLY AVAILABLE WITH -01 & -02 LEAD .003 0.08 C C .050 1.27 STYLE) (SEE TABLE 1, SHT 7) 2 MAX SWAY (NOT AVAILABLE WITH OPTIONS -A, -LC, -P, (EITHER DIRECTION) C 2 MAX SWAY -RA, -TR, -SA, -K, -WT, -RE1, -RE2, -SN, -SN2) (EITHER DIRECTION) (-01 LEAD STYLE USES TFM-XX-D-01-DSL & T1-M2-4-VSFM-T, 02 LEAD STYLE USES SECTION TFM-XX-D-01-DSA & T1-M2-4-VSFM-T) (No OF POSITIONS x .050 1.27 ) - .050 1.27 PROPRIETARY NOTE UNLESS OTHERWISE SPECIFIED, * * C THIS DOCUMENT CONTAINS CONFIDENTIAL AND DIMENSIONS ARE IN INCHES. PROPRIETARY INFORMATION AND ALL DESIGN, TOLERANCES ARE: MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC, DECIMALS ANGLES INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE .003 0.08 C .XX: .01 0.3 2 OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR 520 PARK EAST BLVD, NEW ALBANY, IN 47150 FIG 1 REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY (SEE TABLE 1, .XXX: .005 0.13 PHONE: 812-944-6733 FAX: 812-948-5047 OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS THROUGH HOLE .XXXX: .0020 0.051 SHT 7) WRITTEN CONSENT OF SAMTEC, INC. e-Mail info SAMTEC.com code 55322 -01, -03, -11, -13, -21, -23, -31 MATERIAL: DO NOT SCALE DRAWING SHEET SCALE: 2.5:1 DESCRIPTION: INSULATOR: .050 X .050 TERMINAL STRIP LCP, UL 94-VO DWG. NO. COLOR: BLACK IN-PROCESS TFM-1XX-XX-XXX-D-XXX TERMINAL: PHOSPHOR BRONZE F: DWG MISC MKTG TFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW BY: garyp 11/5/2014 SHEET OF1 7.217 5.50.006 0.15 REVISION FD REF (SEE TABLE 1, (SEE TABLE 1,SHT 7) 90 SHT 7) C C 3 2 SEE NOTE 6 C SEE NOTE 12 FLUSH TO .012 0.30 MAX (SEE NOTE) 7 (-12, -22 & -32 STYLES) SEE NOTE 10 (SEE NOTE 7) 3 (-02 STYLE ONLY) C (SEE NOTE) 3 MAX SWAY .235 5.97 MAX (EITHER DIRECTION) (SEE TABLE 1, 01 03 SHT 7) SECTION 02 No OF POSITIONS x .050) - .050 1.27 SEE NOTE 10 NOTE: R = OVERALL LENGTH (REF) .005.020 0.130.508 (TOL ACCUM .005 0.13 S = (R - .216 5.49 /2 .020 .51 FIG 2 OVER 50 POS) SURFACE MOUNT FIG 3 -02, -12, -22, -32 -K: POLYIMIDE FILM PAD DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1 NOTCH TO BE REF TERMINAL 2 ORIENTED AS SHOWN (SEE TABLE 1, SHT 7) (SEE TABLE 1, 02 SHT 7) TFM-XX-D-XX-WT TERMINAL 1 (No OF POSITIONS X .050 1.27 ) + .263 6.68 REF (SEE TABLE 1, SHT 7) WT-25-04-T .075 1.91 REF 01 .014 0.36 C REF (TYP) .093 2.36 (TYP) 2 MAX SWAY .020 0.51 C C 90 (EITHER DIRECTION) .010 0.25 (SEE NOTE 9 & REF (TYP) C TABLE 1, SHT 7) .025 0.64 REF (No OF POSITIONS x .050 1.27 ) + .154 3.91 SECTION C .050 1.27 2 MAX SWAY (SEE NOTE 9 & (EITHER DIRECTION) TABLE 1, SHT 7) SECTION FIG 5 -RA OPTION FIG 6 DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1 -WT OPTION DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1 REF .422 10.72 .422 10.72 TERMINAL 2 (SEE TABLE 1, TERMINAL 2 (SEE TABLE 1, SHT 7) (SEE TABLE 1, SHT 7) SHT 7) F: DWG MISC MKTG TFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW TERMINAL 1 PROPRIETARY NOTE * * .075 1.91 REF THIS DOCUMENT CONTAINS CONFIDENTIAL AND (SEE TABLE 1, PROPRIETARY INFORMATION AND ALL DESIGN, SHT 7) CARRIER STRIP MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC, TERMINAL 1 INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE I.D. MARK 520 PARK EAST BLVD, NEW ALBANY, IN 47150 OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR (SEE TABLE 1, SHT 7) PHONE: 812-944-6733 FAX: 812-948-5047 REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS C e-Mail info SAMTEC.com code 55322 90 .020 0.51 C WRITTEN CONSENT OF SAMTEC, INC. DESCRIPTION: DO NOT SCALE DRAWING .050 X .050 TERMINAL STRIP IN-PROCESS 1 DWG. NO. (ORIENT I.D. MARK AS SHOWN) SHEET SCALE: 2:1 IN-PROCESS 2 (FOR -RA OPTION ONLY) TFM-1XX-XX-XXX-D-XXX BY: garyp 11/5/2014 SHEET OF2 7