FN9266SB-1-06

DATASHEET IEC Inlet Filters FN 9266 High Performance Power Entry Module with Switch Rated currents up to 10 A Approvals High quality 2-pole rocker switch Optional safety version (A type) Complies with IEC/EN 60601-1 (B type) Snap-in versions (S type) Good attenuation performance The FN 9266 power entry module combines an IEC inlet, mains filter with very high filter attenuation based on nano crystalline material selection and a Performance indicators switch in a small form factor. Choosing FN 9266 product line brings you rapid availability of a standard filter associated with the necessary safety acceptances. Standard IEC connector filters are a practical solution helping you to pass EMI system approval in a short time. A wide selection on amperage ratings, mounting possibilities and filters for medical applications (acc. to IEC 60601-1 with low leakage current and high performance) are designed to offer you the desired solution. Features and benefits Excellent conducted attenuation performance, Technical specifications based on chokes with high saturation resistance and good thermal behavior Operating voltage 250 VAC, 50/60 Hz High quality 2-pole rocker switch for all-pole DC to 400 Hz Operating frequency disconnection Rated currents 1 to 10 A 40C max. Faston terminals for easy assembly High potential test voltage P > PE 2000 VAC for 2 sec (Standard) B types comply with the requirements of IEC/EN P > PE 2500 VAC for 2 sec (B-types) 60601-1 (1MOPP) for creepage and clearance, P > N 760 VAC for 2 sec leakage current and high potential testing Protection category IP 40 according to IEC 60529 As flange mount and snap-in types available -25C to +85C (25/85/21) Temperature range (operation and storage) Design corresponding to UL 60939-3, CSA Std C22.2 No. 8, IEC/EN 60939-3, GB/T 15287, GB/T 15288 Typical applications Flammability corresponding to Inlet plastic: UL 94 V-0 Switch plastic: UL 94 V-0 Medical electrical devices (MD) and In-Vitro MTBF Rated amb. Temp./Voltage (Mil- 2,100,000 hours Diagnostic (IVD) medical devices HB-217F) Portable electrical and electronic equipment Rocker switch description EDP and office equipment Function 2-pole, dark not illuminated Single-phase power supplies Marking I 0 Switch-mode power supplies Electrical specifications Inrush current 100 A 50,000 on-off operations for 10 A according to EN Test and measurement equipment 610581-1 Switch ratings Typical electrical schematic Europe (ENEC) 10 A (4 A), 250 VAC* 5E4 16 A (4 A), 250 VAC* 1E4 20 A, 125 VAC 1 HP 250 VAC 2 HP USA (UL) * Value in () relates to the inductive current charge: cos = 0.652 EMC/EMI Products Schaffner Group Datasheets 06 Jun 2019 Filter selection table Capacitance Filter Rated current Leakage current* Inductance Resistor Output Weight 40C 250 VAC/50 Hz L Cx Cy R connections ( 120 VAC/60 Hz) A mA mH F nF k g FN 9266-1-06 1 0.31 (0.18) 40 0.15 2.2 1000 -06 55 FN 9266-2-06 2 0.31 (0.18) 20 0.15 2.2 1000 -06 55 FN 9266-4-06 4 0.31 (0.18) 7 0.15 2.2 1000 -06 55 FN 9266-6-06 6 0.31 (0.18) 3 0.15 2.2 1000 -06 55 FN 9266-10-06 10 0.31 (0.18) 1.15 0.15 2.2 1000 -06 55 FN 9266A-1-06 1 0.07 (0.04) 40 0.15 0.47 1000 -06 55 FN 9266A-2-06 2 0.07 (0.04) 20 0.15 0.47 1000 -06 55 FN 9266A-4-06 4 0.07 (0.04) 7 0.15 0.47 1000 -06 55 FN 9266A-6-06 6 0.07 (0.04) 3 0.15 0.47 1000 -06 55 FN 9266A-10-06 10 0.07 (0.04) 1.15 0.15 0.47 1000 -06 55 FN 9266B-1-06 1 0.00 40 0.15 1000 -06 55 FN 9266B-2-06 2 0.00 20 0.15 1000 -06 55 FN 9266B-4-06 4 0.00 7 0.15 1000 -06 55 FN 9266B-6-06 6 0.00 3 0.15 1000 -06 55 FN9266B-10-06 10 0.00 1.15 0.15 1000 -06 55 ** Leakage current under normal operating conditions (acc. to IEC60939-3). Note: if the neutral line is interrupted, worst case leakage could reach twice this level. Product selector For example: FN 9266-1-06, FN 9266 SB-10-06