TSH330 1.1 GHz Low-Noise Operational Amplifier Bandwidth: 1.1GHz (Gain=+2) Pin Connections (top view) Quiescent current: 16.6 mA Slew rate: 1800V/s Input noise: 1.3nV/Hz Distortion: SFDR = -78dBc (10MHz, 2Vp-p) Output stage optimized for driving 100 loads D Tested on 5V power supply SO-8 (Plastic Micropackage) Description The TSH330 is a current feedback operational amplifier using a very high-speed complementary technology to provide a large bandwidth of 1.1GHz in gain of 2 while drawing only 16.6mA of quiescent current. In addition, the TSH330 offers NC 1 8 NC 0.1dB gain flatness up to 160MHz with a gain of 2. With a slew rate of 1800V/s and an output stage 2 7 -IN +VCC optimized for driving a standard 100 load, this + +IN 3 6 Output device is highly suitable for applications where speed and low-distortion are the main -VCC 4 5 NC requirements. SO8 The TSH330 is a single operator available in the SO8 plastic package, saving board space as well as providing excellent thermal and dynamic performances. Applications Communication & video test equipment Medical instrumentation ADC drivers Order Codes Part Number Temperature Range Package Conditioning Marking TSH330ID SO8 Tube TSH330I -40C to +85C TSH330IDT SO8 Tape&Reel TSH330I June 2005 Revision 3 1/19 Obsolete Product(s) - Obsolete Product(s)TSH330 Absolute Maximum Ratings 1 Absolute Maximum Ratings Table 1. Key parameters and their absolute maximum ratings Symbol Parameter Value Unit 1 V 6V CC Supply Voltage 2 V +/-0.5 V id Differential Input Voltage 3 V +/-2.5 V in Input Voltage Range T Operating Free Air Temperature Range -40 to + 85 C oper T Storage Temperature -65 to +150 C stg T Maximum Junction Temperature 150 C j R SO8 Thermal Resistance Junction to Ambient 60 C/W thja R SO8 Thermal Resistance Junction to Case 28 C/W thjc 4 P 830 mW max SO8 Maximum Power Dissipation ( Ta=25C) for Tj=150C 5 2kV HBM: Human Body Model (pins 1, 4, 5, 6, 7 and 8) HBM: Human Body Model (pins 2 and 3) 0.6 kV 6 200 V MM: Machine Model (pins 1, 4, 5, 6, 7 and 8) ESD MM: Machine Model (pins 2 and 3) 80 V CDM: Charged Device Model (pins 1, 4, 5, 6, 7 and 8) 1.5 kV CDM: Charged Device Model (pins 2 and 3) 1 kV Latch-up Immunity 200 mA 1) All voltages values are measured with respect to the ground pin. 2) Differential voltage are non-inverting input terminal with respect to the inverting input terminal. 3) The magnitude of input and output voltage must never exceed V +0.3V. CC 4) Short-circuits can cause excessive heating. Destructive dissipation can result from short circuit on amplifiers. 5) Human body model, 100pF discharged through a 1.5k resistor into pMin of device. 6) This is a minimum Value. Machine model ESD, a 200pF cap is charged to the specified voltage, then discharged directly into the IC with no external series resistor (internal resistor < 5 ), into pin to pin of device. Table 2. Operating conditions Symbol Parameter Value Unit 1 V 4.5 to 5.5 V CC Supply Voltage V Common Mode Input Voltage -Vcc+1.5V, +Vcc-1.5V V icm 1) Tested in full production at 5V (2.5V) supply voltage. 2/19 Obsolete Product(s) - Obsolete Product(s)