Automation Controls Catalog
SUBMINIATURE,
TURQUOISE STROKE
LONG STROKE
SEALED SWITCHES
MINI SWITCHES
FEATURES TYPICAL APPLICATIONS
Miniaturization achieved with Automobiles (detection of door
8.3 (Unit: mm)
5.3
changing from 1 Form C to 1 Form A opening and closing, shift lever
or 1 Form B contacts. position, etc.)
7.85
(For the terminal type, volume has Household appliances (vacuum
been cut 45% compared to our cleaners, air conditioners, washing
8.3
previous product.) machines, etc.)
5.3
Lever installation possible while
being miniature.
Terminal type
13.55
Operation possible in various moving
parts such as metal cams.
Contact pressure does not depend
on the operation stroke.
High contact reliability to support
low level switching loads.
Highly effective sealing for resis-
Wire leads type
tance against adverse environments.
(IP67)
RoHS compliant
Silent operation with sliding contact.
ORDERING INFORMATION
ASQM1
Mounting
1: Without boss type (wire leads type only)
6: Right 2 boss type (terminal type only)
7: Left 2 boss type (terminal type only)
Terminal
4: Terminal type (Solder terminal)
6: Wire leads type
Contact form
2: Normally Closed type (NC)
3: Normally Open type (NO)
Actuator
0: Pin plunger
8: Simulated roller lever
Note: Not every combination is available. Please refer to the following table, PRODUCT TYPES.
PRODUCT TYPES
1. Terminal type (solder terminal) Carton: 1,000 pcs.
Right 2 boss type Left 2 boss type
Actuator
NC type NO type NC type NO type
Pin plunger ASQM16420 ASQM16430 ASQM17420 ASQM17430
Simulated roller lever ASQM16428 ASQM16438 ASQM17428 ASQM17438
2. Wire leads type Carton: 240 pcs.
Actuator NC type NO type
Pin plunger ASQM11620 ASQM11630
Simulated roller lever ASQM11628 ASQM11638
industrial.panasonic.com/ac/e/ Panasonic Corporation 2013 AECTB55E 201311-T
2013.11
1
NewTurquoise Stroke mini Switch
RATING
1. Rating
1 mA, 5 V DC to 50 mA, 16 V DC
2. Operation environment and conditions
Item Specications
Ambient and storage temperature 40C to +85C (no freezing and condensing)
Allowable operating speed 30 to 500 mm/sec.
Max. operating cycle rate 120 cpm
Note: When switching at low and high speeds or under vibration, or in high-temperature, high-humidity environments, life and performance may be reduced signicantly
depending on the load capacity. Please consult us.
3. Electrical characteristics
Item Specications
Between non-continuous terminals: 500 Vrms, Between each terminal and other exposed metal parts: 1,500 Vrms,
Withstand voltage (Initial)
Between each terminal and ground: 1,500 Vrms (at detection current of 1 mA)
Insulation resistance (Initial) Min. 100 M (at 500 V DC insulation resistance meter) (Locations measured same as withstand voltage.)
Contact resistance (Initial) Max. 500 m (By voltage drop 50 mA 6 to 8 V DC)
4. Characteristics
Item Specications
5
5 V DC 1 mA (resistive load) Min. 3 10 Switching frequency: 20 times/min.
Electrical Conduction ratio: 1:1
5
12 V DC 50 mA (resistive load) Min. 2 10
switching life Plunger operation speed: 100 mm/s
5
16 V DC 50 mA (resistive load) Min. 1.5 10
Plunger switching position: Free Position (F.P.) to Total Travel Position (T.T.P.)
Single amplitude: 0.75 mm
Amplitude of vibration: 10 to 55 Hz (4 minutes cycle)
Direction and time: 30 minutes each in X, Y and Z directions
Vibration resistance
(malfunction vibration resistance)
Amplitude of vibration: 5 to 200 Hz (10 minutes cycle)
2
Acceleration: 43.1 m/s
Direction and time: 30 minutes each in X, Y and Z directions
2
Shock resistance Shock value: 980 m/s
(malfunction shock resistance) Direction and time: 5 times each in X, Y and Z directions
Terminal strength 6 N min. (each direction) *Terminal deformation possible.
Heat resistance 85C 500 hours
Cold resistance 40C 500 hours
Humidity resistance 40C 95% RH 500 hours
Water resistance IP67 (Wire leads type)
Notes: As long as there are no particular designations, the following conditions apply to the test environment.
Ambient temperature: 5 to 35C
Relative humidity: 25 to 85% RH
Air pressure: 86 to 106 kPa
5. Protective structure
1) JIS C0920 (water-resistance experiments for electrical 3) JIS D0203 (method for testing moisture resistance and water
machines and protection rating against incursion of solid resistance in automotive components): Equivalent of D2 (Note 2)
substances): Immersion protected (Note 1)
Note 1) A concrete testing method is to check for any adverse effect on the structure
after leaving it submerged for 30 minutes under 1 m of water (with
2) IEC 60529 (rating for outer shell protection): IP67 (Immersion
temperature difference between water and switch no larger than 5C).
protected) (Note 1)
Note 2) A concrete testing method is to check for any adverse effect on the structure
except metal terminal part (See below drawing)
after leaving it submerged for 10 minutes under 10 cm water (with
temperature difference between water and switch no larger than 30C).
Metal terminal part
Panasonic Corporation Automation Controls Buisiness Division
Panasonic Corporation 2013 AECTB55E 201311-T
industrial.panasonic.com/ac/e/
2