V23136B1001X051

Automotive Relays Plug-in Mini ISO Relays Shrouded Power Relay F4 A Pin assignment similar to ISO 7588 part 1 Plug-in terminals Customized versions on request Integrated components (e.g. resistor, diode) Customized marking/color Special cover with bracket Typical applications Cross carline up to 40A for example: ABS control, blower fans, cooling fan, energy management, engine control, fuel pump, heated front screen, lamps: front, rear, fog light, main switch/supply relay, wiper control. F136 fcw3c bw Contact Data Contact Data (continued) 6 Contact arrangement 1 form A, 1 NO 1 form C, 1 CO Mechanical endurance >1x10 ops Rated voltage 12VDC 12VDC 1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current Limiting continuous current NO NO/NC duration of maximum 3s for a make/break ratio of 1:10. 23C, form A/form B 60A 60/45A 2) Current and time are compatible with circuit protection by a typical automotive fuse. 85C, form A/form B 40A 40/30A Relay will make, carry and break the specified current. 125C, form A/form B 17A 17/12A 3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at 1) Limiting making current Automotive Relays Plug-in Mini ISO Relays Shrouded Power Relay F4 A (Continued) Insulation Data Other Data (continued) Initial dielectric strength Terminal type plug-in, QC between open contacts 500V Cover retention rms between contact and coil 500V pull force 150N rms between adjacent contacts 500V push force 200N rms Load dump test Terminal retention ISO 7637-1 (12VDC), test pulse 5 V =+86.5VDC pull force 100N s ISO 7637-2 (24VDC), test pulse 5 V =+200VDC push force 100N s Weight approx. 60g (2.1oz) Packaging unit 108 pcs. 6) Refers to used materials. Other Data 7) No change in the switching state >10s. Valid for NC contacts, NO contact values EU RoHS/ELV compliance compliant significantly higher. 6) Protection to heat and fire according UL94 HB or better Ambient temperature -40 to 125C Climatic cycling with condensation Accessories EN ISO 6988 6 cycles, storage 8/16h For fitting connectors please contact us via online Support Center Temperature cycling IEC 60068-2-14, Nb 10 cycles, -40/+85C (5C/min) Damp heat cyclic IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55C Damp heat constant, IEC 60068-2-3, Ca 56 days Category of environmental protection, IEC 61810 RT III sealed Degree of protection, IEC 60529 IP67 (sealed) only with special connector Corrosive gas 3 3 IEC 60068-2-42 102cm /m SO , 10 days 2 3 3 IEC 60068-2-43 10.3cm /m H S, 10 days 2 Vibration resistance (functional) 7) IEC 60068-2-6 (sine sweep) 10 to 500Hz, min. 5g Shock resistance (functional) 7) IEC 60068-2-27 (half sine) 11ms, min. 20g Drop test, free fall, IEC 60068-2-32 1m onto concrete Terminal Assignment NOR COR 1 form A, NO with resistor 1 form C, CO with resistor 2 5 2 54 1 3 1 3 2 02-2017, Rev. 0217 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, Definitions sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications 2017 TE Connectivity. together with the Definitions section. the Definitions section, available at are subject to change.