THDP0200

High-voltage Differential Probes TMDP0200 - THDP0200 - THDP0100 - P5200A - P5202A - P5205A - P5210A BNC interface (P5200A probes) TekVPI interface (TMDP and THDP Series probes) TekProbe interface (P5202A, P5205A, and P5210A Series probes) Safe high-voltage probe solutions The THDP0100 and P5210A have the largest differential dynamic range capability from Tektronix, allowing users to safely measure up to 6000 V. The THDP0100 supports bandwidths up to 100 MHz and slew rates up to 2500 V/ns at 1/1000 gain. These probes are supplied with two sizes of hook tips and have an overrange visual and audible indicator which warns the user when they are exceeding the linear range of the probe. The THDP0200 and P5205A are active differential probes that are capable of safely measuring differential voltages up to 1500 V. The probes are Tektronix offers a broad portfolio of high-voltage probing solutions that effective in making measurements in IGBT circuits such as motor drives enable users to safely and accurately make floating measurements. and power converters. The THDP0200 supports bandwidths up to 200 MHz and slew rates up to 650 V/ns at 1/500 gain. Key performance specifications The TMDP0200 and P5202A are designed for medium-voltage applications Bandwidths up to 200 MHz with differential requirements up to 750 V. These probes have lower attenuation ranges and offer better signal-to-noise ratio. Up to 6000 V differential (DC + pk AC) The P5200A can be used with any oscilloscope and enables users to safely Up to 2300 V common (RMS) make measurements of floating circuits with their oscilloscope grounded. The P5200A Active Differential Probe converts floating signals to low- Key features voltage ground-referenced signals that can be displayed safely and easily on any ground-referenced oscilloscope. Overrange Indicator Safety Certified Connectivity options Switchable Attenuation The TMDP and THDP Series probes are equipped with the TekVPI Switchable bandwidth limit interface which allows smart communication between the oscilloscope and probe. Pushing the probe menu button will launch the probe control menu Applications on the oscilloscope display providing access to all relevant probe settings and controls. These probes are designed to operate on TekVPI Floating measurements oscilloscopes without requiring the TPA-BNC adapter. Switching power supply design The P52xxA Series probes are equipped with the Tektronix TekProbe Motor drive design interface which communicates scale information to the oscilloscope. Direct connections can be made to oscilloscopes configured with the TekProbe Electronic ballast design interface or to any oscilloscope when used with the 1103 TekProbe Power CRT display design Supply. Power converter design and service Power device evaluation www.tek.com 1High Voltage Differential Probe Datasheet Specifications All specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise. Model overview Probes with the TekVPI interface TMDP0200 THDP0200 THDP0100 Attenuation 25X / 250X 50X / 500X 100X / 1000X Differential Voltage 250X: 750 V 500X: 1500 V 1000X: 6000 V 25X: 75 V 50X: 150 V 100X: 600 V Common Mode Voltage 750 V 1500 V 6000 V Maximum Input Voltage-to-Earth 550 V CAT I 1000 V CAT II 2300 V CAT I 300 V CAT III 600 V CAT III 1000 V CAT III Bandwidth 200 MHz 200 MHz 100 MHz Rise Time <1.8 ns <1.8 ns <3.5 ns Slew Rate <275 V/ns at 1/250 gain <650 V/ns at 1/500 gain <2500 V/ns at 1/1000 gain Input Impedance at the Probe Tip 5 M <2 pF 10 M <2 pF 40 M <2.5 pF Typical CMRR DC: > -80 dB DC: > -80 dB DC: > -80 dB 100 kHz: > -60 dB 100 kHz: > -60 dB 100 kHz: > -60 dB 3.2 MHz: > -30 dB 3.2 MHz: > -30 dB 3.2 MHz: > -30 dB 100 MHz: > -26 dB 100 MHz: > -26 dB 100 MHz: > -26 dB Cable Length 1.5 m 1.5 m 1.5 m Probes with the BNC and TekProbe interface P5200A P5202A P5205A P5210A Attenuation 50X / 500X 20X / 200X 50X / 500X 100X / 1000X Differential Voltage 500X: 1300 V 200X: 640 V 500X: 1300 V 1000X: 5600 V 50X: 130 V 20X: 64 V 50X: 130 V 100X: 560 V Common Mode Voltage 1300 V 640 V 1300 V 5600 V Maximum Input Voltage-to-Earth 1000 V CAT II 450 V CAT l 1000 V CAT II 2300 V CAT l 300 V CAT ll 1000 V CAT III Bandwidth 50 MHz 100 MHz 100 MHz 50 MHz Differential Input Impedance 10 M 2 pF 5 M 2 pF 10 M 2 pF 40 M 2.5 pF Input Impedance between each 5 M 4 pF 2.5 M 4 pF 5 M 4 pF 20 M 5 pF Input and Ground Typical CMRR DC: >80 dB DC: >80 dB 100 kHz: >60 dB 100 kHz: >60 dB 3.2 MHz: >30 dB 3.2 MHz: >40 dB 50 MHz: >26 dB 50 MHz: >30 dB Cable length 1.8 m 2 www.tek.com