Photologic Slotted Optical Switch OPB960, OPB970, OPB980, OPB990 Series Features: Choice of logic and output driver circuits Choice of aperture size, covered or open Wire or PCB leads Choice of mounting features Direct TTL, LSTTL, CMOS Interface Description: The OPB960/ 970/ 980/ 990 series of non-contact Photologic slotted optical switches provides flexibility in meeting application specific requirements for the design engineer. Building from a standard housing with a 0.125 (3.18mm) wide slot, the user can specify output logic state, output driver circuit, aperture width, aperture surface and mounting tab locations. Furthermore, an option of wire or PCB leads allows electrical interface flexibility. The device body is an opaque plastic which minimizes sensitivity to both visible and near-infrared external light sources which may impact operation. Aperture width choices provide different optical resolution for motion sensing. A covered aperture provides dust protection, while an open aperture provides maximum protection against external light sources. Electrical operation is over a wide supply voltage range. LED emissions are near-infrared (850940nm). Detector digital output logic choices of buffer or inverter with totem-pole or open-collector driver circuit simplify interface for various electrical requirements. Custom electrical, wire and cabling services are available. Contact your local representative or OPTEK for more information. Compliant to EU RoHS Directive 2002/95/EC . For more information see Application notes 201, 213 Applications: Speed and direction indication Mechanical switch replacement Printers - Top of form, End of travel, Home position. Rotary encoders Mechanical limit indication Sliding Door Automotive and Lift gate applications Part Number Guide OPB 9XX X XX X OPTEK Assembly Z = Wires only, None for PCB leads Photologic Sensor Family Aperture Width Guide Options: 55, 51, 11 ( See Aperture Width Guide ) Slot Aperture Surface and Lead Options: 6 Covered (apertures not visible), PCB leads 7 Open (apertures visible), PCB leads Mounting Tab Location: 8 Covered (apertures not visible), Wires L Emitter 9 Open (apertures visible), Wires N None P Sensor Logic and Output Driver Types: T Both (two mounting tabs) 0 Buffer Totem-Pole 1 Buffer Open-Collector 2 Inverter Totem-Pole 3 Inverter Open-Collector Input Output Logic Type LED Logic State Buffer OFF LOW = 0 Inverter OFF HIGH = 1 RoHS OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Issue C.1 1/10 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors optekinc.com www.optekinc.com Page 1 of 6 Photologic Slotted Optical Switch OPB960, OPB970, OPB980, OPB990 Series PACKAGE OUTLINE for OPB960 and OPB970 Series TABLE 1 APERTURE WIDTH GUIDE Lead No. Function CODE LED SENSOR 1 Anode 55 .050 1.27mm .050 1.27mm 2 Cathode 51 .050 1.27mm .010 0.25mm 3 Vcc 11 .010 0.25mm .010 0.25mm Lengths are .050 1.27mm 4 Output 5 Ground Notes: (1) RMA flux recommended. Duration can be extended to 10 seconds max. (2) Feature controlled at body. (3) Highly activated water soluble fluxes may attack plastic. Recommend trial to verify application. (4) Maximum lead soldering temperature 1.6mm from case for 5 seconds with soldering iron 260 C. (5) Cathode lead may be shorter. (6) Part number marking may be on any side. OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible. Issue C.1 1/10 OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Page 2 of 6 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors optekinc.com www.optekinc.com