Vertical Cavity Surface Emitting Laser in Lateral Package OPV380 850nm VCSEL technology High thermal stability Low drive current High output power Flat lens package The OPV380 is a Vertical Cavity Surface Emitting Laser (VCSEL) packaged in a flat lens lateral package. VCSELs offer many advantages in sensing applications when compared to infrared LEDs. These devices require substantially lower drive currents to obtain the same amount of output power as LEDs. This feature allows VCSELs to be used in low power consumption applications such as battery operated equipment. The flat lens packaging allows the device to be used with secondary optics to create custom beam profiles. The OPV380 is optically and spectrally compatible with Opteks standard detector products such as the OP550 series phototransistors, OP530 series photodarlingtons and the OP900 series photodiodes. Applications Non-contact position sensing Photoelectric sensors Emission Surface Optical encoders Light curtains VCSEL Additional laser safety information can be found on the Optek website. See application bulletin 221. Classification is not marked on the device due to space limitations. See Pb package outline for centerline of 1 2 optical radiance. Operating devices beyond maximum rating may result in hazardous radiation exposure. RoHS Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 A subsidiary of Phone: (800) 341-4747 FAX: (972) 323 2396 sensors optekinc.com www.optekinc.com TT electronics plc VCSEL in Flat Lens Lateral Package OPV380 Absolute Maximum Ratings o T = 25 C unless otherwise noted A Storage Temperature Range -40 to +100 C Operating Temperature Range 0 to +85 C (1) Lead Soldering Temperature 1/16 inch (1.6mm) from case for 5 sec with soldering iron 260 C Maximum Forward Peak Current, Continuous 12 mA Maximum Reverse Voltage 5 V Maximum Forward Current, pulsed (1s P.W., 10% D.C.) 48 mA Electrical Characteristics (T = 25C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS CONDITIONS P Total Power Out 1.5 mW I = 7 mA OT F I Threshold Current 3.0 mA Note 2 TH V Forward Voltage 2.2 V I = 7 mA F F I Reverse Current 100 nA V = 5 V R R R Series Resistance 20 55 ohms Note 3 S Slope Efficiency 0.28 mW/mA Note 4 Wavelength 840 860 nm Optical Bandwidth 0.85 nm Beam Divergence 20 Degrees FWHM /T Temp Coefficient of Slope Efficiency -0.50 %/C (0 - 70C), Note 4 nm/C (0 - 70C) /T Temp Coefficient of Wavelength 0.06 Temp Variance of Threshold Current 1.0 (0 - 70C), Note 2 l mA TH Temp Coefficient for Forward Voltage -2.5 mV/C (0 - 70C) V /T F NOTES: (1) RMA flux is recommended. Solder dwell time can be increased to 10 seconds when flow soldering. (2) Threshold Current is based on the two line intersection method specified in Telcordia GR-468-Core. Line 1 from 4 mA to 6 mA. Line 2 from 0 mA to 0.5 mA. (3) Series Resistance is the slope of the Voltage-Current line from 5 to 8 mA. (4) Slope efficiency, is the slope of the best fit LI line from 5 mA to 8 mA with 0.25mA test intervals. Normalized Output Power vs. Typical Angular Output Forward Current 100% 200% Normalized at 7mA, 25C 80% 60% 100% 40% 20% 0% 0% 0 -90 60 -60 -30 0 30 90 2 4 6 8 10 12 Angular DisplacementDegrees Forward CurrentmA OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Issue 1.2 09.09 Phone: (800) 341-4747 FAX: (972) 323 2396 sensors optekinc.com www.optekinc.com Page 2 of 2 Relative Output Normalized Output Power