PUP96N3S-12 TT Electronics

96-120 WATT ITE POWER SUPPLIES DESCRIPTION PUP96N3/PUP120N3 SERIES The PUP96N3/PUP120N3 series of AC/DC switching power RoHS supplies are for 96-120 watts of continuous output power. They are enclosed in a 94V-0 rated plastic case with an inlet of the IEC320/C14 or IEC320/C6 to mate with interchangeable cord for world-wide use. All models meet EN55032 and FCC class B emission limits, and comply with UL, CSA, IEC and CE requirements. FEATURES l No load power consumption less than 0.15 W l Compliant with DoE level VI requirements l Meet Energy Star EPS2.0 /ErP EC No 278/2009 (Lot 7) SAFETY STANDARD APPROVALS l Meet EU CoC EPS V5 Tier 2 l Operating altitude up to 5000 meters UL 62368-1, CSA C22.2 No. 62368-1 l Overvoltage protection (latch) File No. E190414 l Short-circuit protection (auto-recovery) l Overpower protection (auto-recovery) l Over temperature protection (latch) l High Efficiency 89% TUV EN 62368-1 l With PFC circuit l 100% burn-in at full rated load l Compliant with RoHS requirements GENERAL SPECIFICATIONS Hold-up time: 10 ms minimum at 100 VAC Turn on delay time: 3 s maximum at 100 VAC INPUT SPECIFICATIONS Power factor: 0.95 typical Input voltage: 90-264 VAC Efficiency: 89% minimum at 110 VAC or 240 VAC. Input frequency: 47-63 Hz Line regulation: 0.5% maximum at full load Input current: 1.3 A (rms) for 115 VAC Inrush current: 100 A @ 115 Vac or 200 A @ 230 Vac at 25 0.7 A (rms) for 230 VAC cold start Earth Leakage current: 250 A max. @ 264 VAC, 60 Hz Withstand voltage: 4242 VDC from input to output 2500 VDC from input to ground MTBF: 200,000 hours at full load at 25 ambient, OUTPUT SPECIFICATIONS calculated per SR332 Output voltage /current: See rating chart. Maximum output power: See rating chart. Ripple and noise: 350 mV peak to peak maximum EMC Performance Overvoltage protection: Set at 125-155% of its nominal EN55032: Class B conducted, Class B radiated output voltage Overcurrent protection: All models protected to short FCC: Class B conducted, Class B radiated circuit conditions (auto-recovery) VCCI: Class B conducted, Class B radiated All outputs 0.04% / maximum Temperature coefficient: EN61000-3-2: Harmonic distortion, Class D Transient response: Maximum excursion of 4% or better on EN61000-3-3: Line flicker all models, recovering to 1% of final EN55024 value within 500 us after a 25% step load change EN61000-4-2: ESD,8 KV air and 4 KV contact EN61000-4-3: Radiated immunity, 3 V/m EN61000-4-4: Fast transient/burst, 1 KV EN61000-4-5: Surge, 1 KV diff., 2 KV com. EN61000-4-6: Conducted immunity, 3 Vrms ENVIRONMENTAL SPECIFICATIONS EN61000-4-8: Magnetic field immunity, 1 A/m Operating temperature: 0 to +40 EN61000-4-11: Voltage dip immunity, 30% reduction for 500 Storage temperature: -20 to +80 ms, and >95% reduction for 10 ms Operating humidity: 20% to 80% non-condensing Storage humidity: 10% to 90% non-condensing 45UNIVERSAL INPUT PUP96N3/PUP120N3 ITE SERIES OUTPUT VOLTAGE/CURRENT RATING CHART Output Average Active efficiency (typical) Min. Max. Ripple & Max. (1) (2) @ 115 / 230 Vac Model V1 Current Current Tol. Noise Power PUP96N3-12 12 V 0 A 8.00 A 5% 350 mV 96 W 89 /90% PUP96N3S-12 12 V 0 A 8.00 A 5% 350 mV 96 W 89 /90% PUP120N3-12 12 V 0 A 10.00 A 5% 350 mV 120 W 89 /90% PUP120N3S-12 12 V 0 A 10.00 A 5% 350 mV 120 W 89 /90% PUP120N3-14 24 V 0 A 5.00 A 5% 350 mV 120 W 89 /91% PUP120N3S-14 24 V 0 A 5.00 A 5% 350 mV 120 W 89 /91% PUP120N3-18 48 V 0 A 2.50 A 5% 350 mV 120 W 89 /91% PUP120N3S-18 48 V 0 A 2.50 A 5% 350 mV 120 W 89 /91% PUP120N3-19 54 V 0 A 2.22 A 5% 350 mV 120 W 89 /91% PUP120N3S-19 54 V 0 A 2.22 A 5% 350 mV 120 W 89 /91% NOTES: 1. PUP120N3 models are equipped with IEC320/C14 inlet, and PUP120N3S models are equipped with IEC320/C6 inlet. 2. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 47 F tantalum capacitor in parallel with a 0.1 F ceramic capacitor across the output. MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inches [mm] 2. Tolerance 0.02 [0.5] maximum 3. Weight: 417 grams (0.92 lbs.) approx. 4. V1 return (-) is electrically connected to incoming Earth Ground through a 1M ohm resistor as standard. PIN CHART SHELL OF PIN NO. 1 2 3 4 CONNECTOR Polarity +V1 +V1 V1 Return V1 Return V1 Return 46