Item No.: T60403-K5024-X092 Specification V A C U U M S C H M E L Z E K-No.: Date: 25165 22.07.2014 Powerline transformer Customer: Customers part No.: Page 1 of 3 Mechanical outline (mm): (General Tolerances DIN ISO 2768-c) Connections: DC=Date Code Vorschlag zur Anordnung Toleranz der Stiftabstnde Kennzeichnung Stift 1 Dummy pins: 0,2 mm F=Factory der Anschluflchen (marking pin 1) No. (Tolerances grid distance) (Example for pad position ) 0,6x0,4 2,5 1 4 14,6 13,9 11,46 10,16 F DC Beschriftung: marking 5 8 1,3 DC 2,54 1,0 5024X092 7,62 7,1 2,54 F 11 7,6 3x2,54 0,1 Schematic diagram: Operational data/characteristic data (nominal values): f = 101000 kHz IC side mains side 1 8 I < 140 mA (50/60Hz) N1 RMS 2 N3 3 N2 R 250 m R 250 m , R 500 m Cu1 Cu2 Cu3 5 4 Operating temperature: -40 C ... +85 C = 1 : 1 : 2 Storage temperature: -40 C ... +85 C Inspection: (V: 100%-Test AQL...: DIN ISO 2859-Teil1) 1) (V) M3014: U = 4,0 kV, 2 s, N3 vs N1+N2 p,eff U = 0,5 kV, 2 s, N1 vs N2 p,eff 2) (AQL 0,25) M3214: L 700 H, I = 130 mA, f = 10 kHz, U = 100 mV 3 DC AC,eff 3) (V) M3011/6: Polarity, Turns ratio: Tolerance 2 % see page 2 Applicable documents: see page 2 Date Name Index Change 22.07.14 Pf. 84 Characteristic data: I < 140 mA changed to I < 140 mA (50/60Hz). Lapidary change. DC RMS 14.01.14 BZ 84 Inspection 2) changed from M3011/1 to M3214. CN-712 released: HH Editor: KB-E Design: KB-PM: Pf. Bs. check Copying of this document, disclosing it to third parties or using the contents there for any Weitergabe sowie Vervielfltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts purposes without express written authorization by use illegally forbidden. nicht gestattet, soweit nicht ausdrcklich zugestanden. Zuwiderhandlungen verpflichten zu Any offenders are liable to pay all relevant damages. Schadenersatz. Alle Rechte fr den Fall der Patenterteilung oder GM-Eintragung vorbehalten Item No.: T60403-K5024-X092 Specification V A C U U M S C H M E L Z E K-No.: Date: 25165 22.07.2014 Powerline transformer Customer: Customers part No.: Page 2 of 3 Inspection: (V: 100%-Test AQL...: DIN ISO 2859-Teil1) 4) (Fix05) M3291: Solderability test acc. to chapter 1 5) (AQL 1/S4) M3200: Mechanical test Type test 1) High voltage test according to M3014 U = 4 kV, 1 min, N1+N2 vs N3 p,eff 2) M3292: Resistance to soldering heat acc. to chapter 2 Measurements after temperature balance of the test samples at room temperature Remark: The following HV test may be applied one time at the customer after final assembly where the number of reflows has to be limited to one (max): U = 4 kV / 2 s, N1+N2 vs N3 p,eff Measurement has to be performed after temperature balance of the samples to room temperature. Storage conditions before test: max. 30C / max. 50% relative humidity or max. 85C / max. 5% relative humidity. Applicable documents: Designed, manufactured and tested in accordance to EN 60950 (IEC 60950) and complies with the standards. Parameters: Reinforced insulation: N1+N2 to N3 Working voltage: 400 V r.m.s. Overvoltage category: 2 Pollution degree: 2 Insulation material group: 3 Housing material, casting resin and wire UL listed Packing: Drypack / MSL according VAC M3027 released: HH Editor: KB-E Design: KB-PM: Pf. Bs. check Copying of this document, disclosing it to third parties or using the contents there for any Weitergabe sowie Vervielfltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts purposes without express written authorization by use illegally forbidden. nicht gestattet, soweit nicht ausdrcklich zugestanden. Zuwiderhandlungen verpflichten zu Any offenders are liable to pay all relevant damages. Schadenersatz. Alle Rechte fr den Fall der Patenterteilung oder GM-Eintragung vorbehalten