8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REV. DESCRIPTION DATE APPROVED THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. 1 RELEASED PER E053437 LEK 11/15/05 EF SEE NOTE 6 2 REVISED PER E091085 AR 07/10/09 REJH F F 3 REDRAWN PER E100887 DCS 6/8/10 KUK <> 4 REVISED PER E120702 ZMB 07/31/12 REJH 30 DRILL THRU .40 ( .1285 ) <> (6) PL16 TYP .010 (12) PL. MATL SEE NOTE 5 TO BE REMOVED E E <> 2.220 2.000 D D .11 .650 .190 <> 1.300 -A- .49 <> 2.28 .100 <> .005 C C .410 B B NOTES: 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2. 2. REMOVE ALL BURRS AND SHARP EDGES. <> 3. CLEAR FINISH, RoHS COMPLIANT PER CST-0001, LATEST REVISION PER A.) CHROMIUM FREE, OR B.) TRIVALENT CHROMIUM IN ACCORDANCE WITH MIL-DTL-5541, TYPE II, CLASS 1A OR 3. SEE CST-0003 FOR TYPES OF AVAILABLE FINISHES. DRAWN BY DATE SWD VICOR 4.< DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION 5. DIMENSIONS APPLIES AT SURFACE -A- (12) PL. P.E. IENI 06/30/05 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PL. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / MM 7. DIMENSIONS ARE INCHES ONLY. HS CFG LONG .4H LOW TOLERANCES ARE: DECIMALS ANGLES A A FLOW, THRU HOLE X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30195 4 2:1 2 SCALE SHEET OF 1 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 F F E E R.035 (24) PL. SEE DETAIL A R.035 .410 .235 .200 .110 D D 3 * .133 1.5 EACH (9) PL. SIDE OF VERT * .060 R.010 * .138 (8) PL. (2) PL. (2) PL. 1.756 * .058 (2) PL. * .269 R.018 .023 (2) PL. +.020 .017 2.220 .036 -.000 (2) PL. C C .031 .040 .080 R.030 (8) PL252 C L PROFILE COMMON B B FOR 30195 * .030 30718 * .060 NOTES: 32188 1. MATL: ALUMINUM 6063-T5 30482 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. DETAIL A 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS SCALE 8 : 1 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. 5. DIMENSIONS ARE INCHES ONLY SWD DRAWN BY DATE VICOR A. RAGIPANI 07/10/09 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / MM HS CFG LONG .4H LOW TOLERANCES ARE: DECIMALS ANGLES A A FLOW, THRU HOLE, EXTRUSION X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30195 4 SCALE 2:1 2 2 SHEET OF DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1