CS
www.vishay.com
Vishay Dale Thin Film
Ceramic Sandwich, Single-In-Line Thin Film Resistor,
Through Hole Network (Low Profile 0.20 Custom)
FEATURES
Gold-to-gold terminations. External leads are
attached directly to gold pads on the ceramic
substrate by thermo-compression bonding (no
internal solder)
Low profile (0.200 min.)
Custom pin-outs available
Compliant to RoHS Directive 2002/95/EC
Halogen-free according to IEC 61249-2-21
Actual Size
definition
Note
* Pb containing terminations are not RoHS compliant, exemptions
Vishay Dale Thin Film presents a design concept in precision
may apply
thin film resistor networks. The essence of this new concept
is the marriage of two principle design elements . . . a unique TYPICAL PERFORMANCE
resistive film, having electrical properties comparable to
ABSOLUTE TRACKING
those of wire-wound resistors, and a rugged, low cost,
ceramic package and an almost limitless variety of sizes and
TCR 25 2
configurations.
ABSOLUTE RATIO
TOL. 0.05 0.01
SCHEMATIC
Custom schematics available.
Please consult factory.
STANDARD ELECTRICAL SPECIFICATIONS
TEST SPECIFICATIONS CONDITIONS
Material Passivated nichrome Tantalum nitride -
Pin/Lead Number 3 to 10 -
Resistance Range 20 to 2000 k (total) 20 to 500 k (total) -
TCR: Absolute 10 ppm/C to 25 ppm/C 50 ppm/C to 100 ppm/C - 55 C to + 125 C
TCR: Tracking 2 ppm/C 5 ppm/C - 55 C to + 125 C
Tolerance: Absolute 0.05 % to 1.0 % + 25 C
Tolerance: Ratio 0.01 % to 0.5 % 0.02 % to 0.5 % + 25 C
Power Rating: Resistor 100 mW (per element) Typical at + 25 C
Power Rating: Package --
Stability: Absolute R 0.05 % R 0.1 % 2000 h at + 70 C
Stability: Ratio R 0.015 % R 0.02 % 2000 h at + 70 C
Voltage Coefficient < 0.1 ppm/V < 0.1 ppm/V -
Working Voltage 100 V -
Operating Temperature Range - 55 C to + 125 C -
Storage Temperature Range - 55 C to + 150 C -
Noise < - 30 dB -
Thermal EMF < 0.08 V/C -
Shelf Life Stability: Absolute R 0.01 % 1 year at + 25 C
Shelf Life Stability: Ratio R 0.002 % 1 year at + 25 C
Revision: 20-Oct-11 Document Number: 60081
1
For technical questions, contact: thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CS
www.vishay.com
Vishay Dale Thin Film
DIMENSIONS AND IMPRINTING in inches and millimeters
DIMENSION INCHES MILLIMETERS
(1)
A 0.100 typ. 2.54 typ.
L Max.
B 0.020 0.002 typ. 0.51 0.05 typ.
C 0.125 min. 3.17 min.
D 0.100 max. 2.54 max.
E 0.010 0.25
H
L (3 Pins) 0.320 8.13
L (4 Pins) 0.420 10.67
C
L (5 Pins) 0.520 13.21
L (6 Pins) 0.620 15.75
A B
L (7 Pins) 0.720 18.25
L (8 Pins) 0.820 20.83
L (9 Pins) 0.920 23.37
Pin 1
Part Number Date Code
L (10 Pins) 1.020 25.91
H (3 Pins)
H (4 Pins)
H (5 Pins)
H (6 Pins)
(2) (2)
0.200 7.11
H (7 Pins)
H (8 Pins)
Vishay Logo
H (9 Pins)
H (10 Pins)
Notes
(1)
Non-accum.
(2)
Resistance value and schematic dependent. By occupying more than one 0.100 inch square, higher values are available.
MECHANICAL SPECIFICATIONS
Resistive Element Passivated nichrome or tantalum nitride
Substrate Material Alumina
Body Ceramic
Terminals Copper alloy
Plating Gold
Tin/Lead Option Sn63
Lead (Pb)-free Option Sn96.5, Ag3.0, Cu0.5
Tin/Lead and Lead (Pb)-free Finish Hot solder dip
ORDERING INFORMATION CHECK LIST
Special requirements should be identified in advance, but as a minimum, you should have the following information ready.
ELECTRICAL MECHANICAL
1. Resistors, by value and tolerance 1. Maximum allowable seated height (from PC board to top of
network)
2. Reference resistor(s) and matching of which resistors to which
reference resistors 2. Special marking concerns
3. Resistance by ratio 3. Schematic pin out of package
4. Absolute temperature coefficient of resistivity 4. Specify if lead (Pb)-free
5. Temperature tracking of subordinate resistors to reference
resistor(s)
6. Maximum operating voltage
7. Resistor power ratings
8. Operating temperature range
For additional assistance refer to Vishay Dale Thin Films guide to understanding Thin Film precision.
Resistor networks or application engineering.
All standard products may be ordered directly from Vishay Dale Thin Film.
Revision: 20-Oct-11 Document Number: 60081
2
For technical questions, contact: thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000