TSOP6238TT Vishay

333 3 TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against optical noise 4 3 Insensitive to supply voltage ripple and noise 2 1 16797 Taping available for top view and side view assembly Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES Product Page 3D Models Calculators Marking MECHANICAL DATA Pinning 1 = GND, 2 = N.C., 3 = V , 4 = OUT S DESCRIPTION The TSOP6... series are miniaturized SMD IR receiver modules for infrared remote control systems. A PIN diode ORDERING CODE and a preamplifier are assembled on a leadframe, the epoxy Taping: package contains an IR filter. TSOP6...TT - top view taped, 1190 pcs/reel The demodulated output signal can be directly connected to TSOP6...TR - side view taped, 1120 pcs/reel a microprocessor for decoding. The TSOP64.. series devices are optimized to suppress almost all spurious pulses from Wi-Fi and CFL sources. BLOCK DIAGRAM They may suppress some data signals if continuously 3 transmitted. V The TSOP62.. series devices are provided primarily for S 33 k compatibility with old AGC2 designs. New designs should 4 prefer the TSOP64.. series containing the newer AGC4. OUT Band Demo - These components have not been qualified according to Input AGC dulator pass automotive specifications. 1 PIN GND Control circuit 16839-1 APPLICATION CIRCUIT 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 1.8, 26-Mar-2021 Document Number: 82463 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP62.., TSOP64.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR RECOMMENDED FOR AGC LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) 30 kHz TSOP6230 TSOP6430 33 kHz TSOP6233 TSOP6433 (1)(2)(3) 36 kHz TSOP6236 TSOP6436 Carrier frequency (4)(5) 38 kHz TSOP6238 TSOP6438 40 kHz TSOP6240 TSOP6440 (6)(7) 56 kHz TSOP6256 TSOP6456 Package Panhead Pinning 1 = GND, 2 = N.C., 3 = V , 4 = OUT S Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Narrow optical filter: www.vishay.com/doc 81590 Special options Wide optical flter: www.vishay.com/doc 82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S V = 5 V, E = 0 I 0.55 0.7 0.9 mA S v SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH E = 0, IR diode TSAL6200, v Transmission distance d- 18 - m I = 50 mA, test signal see Fig. 1 F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f E -0.2 0.4 mW/m pi o po pi o, e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 50 - - W/m e max. test signal see Fig. 1 Angle of Directivity - 50 - deg 1/2 half transmission distance Rev. 1.8, 26-Mar-2021 Document Number: 82463 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000