TSOP983.., TSOP985.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved dark sensitivity Improved immunity against optical noise Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 3.6 V 1 Material categorization: 22 for definitions of compliance please see 33 19026 www.vishay.com/doc 99912 click logo to get started DESIGN SUPPORT TOOLS MECHANICAL DATA 1 = OUT, 2 = GND, 3 = V S Models Available DESCRIPTION The TSOP98... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. Th e demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP983.. and TSOP985.. series devices are designed to receive short burst codes (6 or more carrier cycles per burst). The third digit designates the AGC level (AGC3 or AGC5) and the last two digits designate the band-pass frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC3 provides enhanced noise suppression and AGC5 provides maximized noise suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. These components have not been qualified to automotive specifications. PARTS TABLE ENHANCED NOISE SUPPRESSION MAXIMIZED NOISE SUPPRESSION AGC (AGC3) (AGC5) 30 kHz TSOP98330 TSOP98530 33 kHz TSOP98333 TSOP98533 (1) 36 kHz TSOP98336 TSOP98536 Carrier frequency (2)(4) 38 kHz TSOP98338 TSOP98538 40 kHz TSOP98340 TSOP98540 (3) 56 kHz TSOP98356 TSOP98556 Package Minicast Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Remote control (1) (2) (3) (4) Best choice for RCMM RECS-80 Code r-map XMP-1, XMP-2 Note 30 kHz and 33 kHz only available on written request Rev. 1.2, 11-Dec-2018 Document Number: 82833 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP983.., TSOP985.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833-13 17170-12 R 1 3 Transmitter IR receiver with V + V 30 k S S TSALxxxx C 1 1 C Band Demo- OUT Input AGC pass dulator V O GND GND 2 PIN Control circuit R and C recommended to reduce supply ripple for V < 2.2 V 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +3.6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.25 0.37 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.50- mA v SH Supply voltage V 2.0 - 3.6 V S E = 0, test signal see Fig. 1, v Transmission distance d- 21 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V -- 100 mV OSL e OSL Test signal: XMP code - 0.20 0.40 2 Minimum irradiance E mW/m e min. Test signal: NEC code - 0.15 0.30 2 Maximum irradiance t - 3.0/f < t < t + 3.5/f , test signal see Fig. 1 E 30 - - W/m pi 0 po pi 0 e max. Directivity Angle of half transmission distance - 45 - 1/2 Rev. 1.2, 11-Dec-2018 Document Number: 82833 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 Circuit