124 114111

WHITE-RODGERS DC PRODUCTS Type 124 solenoid FEATURES Double-make or double-break contacts Steel enclosure Offers high and low current capabilities Isolated or grounded coils ENGINEERING DATA Contacts Pole for mSPNO, SPNC and SPDT GENERAL DATA Mater ialsilver alloy 5 Dielectr ic Strength Ter mination /16-24 UNF-2A thread 500 Volts RATINGS Temperature Range NO NC -40F/-40C to 149F/65C Volts DC Cont. Inrush Cont. Inrush Mechanical Life (no load) 6 150A 400 A 50A 200 A 100,000 operations 12 150 A 400 A 50 A 200 A Electr ical Life (rated load) 24 150 A 400 A 50 A 100 A 36 100 A 400 A 50 A 100 A 50,000 operations Mounting Position Coils Recommended mounting is ver tical plane Voltage6 VDC through 48 VDC with coil ter minals up Ter mination 10-32 UNF-2A thread Weight (approximate) Power (approximate) SPNO16.0 oz. Continuous 12 watts SPDT19.0 oz. Inter mittent 24 watts Duty Cycle Connections Continuous 1. Coil isolated (two ter minals) Inter mittent10 seconds on maximum 2. One coil lead grounded to case and minimum 60 seconds off (one ter minal) One minute on maximum and minimum 6 Operate (77F/25C) minutes off 75% of nominal coil voltage Hardware Torque Specification 110% max. safe of nominal coil voltage Contact Ter minal: 60 inch-lbs. max. Coil Ter minal: 12-18 inch-lbs. COIL DATA Resistance in Ohms Volts DC Intermittent Continuous 6 1.7 3.3 12 6.6 13.2 15 10.2 21.0 24 26.0 53.0 36 59.0 120.0 48 105.0 213.0 St. Louis, Missour i Mar kham, Ontar io 314-553-3600 905-948-4711 The Emerson logo is a R-4004C trademark and a service mark www.white-rodgers.com 1232 of Emerson Electric Co.TYPE 124 PART NUMBERING SYSTEM 124 x xx x x x - x Basic Part Number Series Mounting Bracket Coil Coil 1 Standard bracket Voltage/Duty Termination 02 6 Volt continuous 1 Isolated Contact 03 6 Volt intermittent 2 Grounded Form Factory Assigned Specials 05 12 Volt continuous 1 SPNO (where undefined, contact factory) 06 12 Volt intermittent 2 SPNC 08 15 Volt continuous No dash Standard assem- 3 SPDT Contact 09 15 Volt intermittent bly, hardware sent bulk Material 14 24 Volt continuous 1 Customer requested markings 15 24 Volt intermittent 1 AgCdO 2 Customer requested markings 17 36 Volt continuous 4 AgCdO (to be replaced 3 Customer requested markings 18 36 Volt intermittent by 1) 4 Customer requested markings 20 48 Volt continuous 5 Au plated NC/AgCdO NO 5 Customer requested markings 21 48 Volt intermittent 6 Customer requested markings APPLICATION NOTES Not all par t number combinations are available. Please contact your Sales Representative for available par t numbers. Solenoids applied in batter y charging circuits should be protected from higher than rated voltage dur ing charging. The ser vice life may be affected by this condition and the solenoid may or may not operate the circuit as intended. Circuits should be designed to provide safe operation should the solenoid fail in either the open or closed position. A back-up wrench must be used to hold the bottom nut stationar y dur ing installation. SPNO Isolated Coil .281 WIDE X .500 LONG SLOT H 2.188 10-32 .547 NORMALLY UNF-2A X 1.274 OPEN .350 LONG 1.156 2.313 W 3.062 CIRCUIT DIAGRAM 5/16-24UNF-2A X .547 (USABLE) LENGTH 1.234 L MAX. 3.619 Coil Grounded to Case 10-32 .281 WIDE x .500 LONG SLOT UNF-2A X H 2.188 .547 NORMALLY .350 LONG OPEN 2.313 1.156 W 3.062 5/16-24UNF-2A X .547 (USABLE) LENGTH 1.234 CIRCUIT DIAGRAM L MAX. 3.619 SPDT Isolated Coil 10-32 .281 WIDE X .500 LONG SLOT H 2.188 UNF-2A X 1.274 NORMALLY .547 NORMALLY .350 LONG CLOSED OPEN 1.156 2.313 W 3.062 5/16-24UNF-2A X .547 (USABLE) LENGTH 2.367 L MAX. CIRCUIT DIAGRAM 4.752 R-4004C 1232