MKS0C023300B00KSSD WIMA

D WIMA MKS 02 Metallized Polyester (PET) Capacitors in PCM 2.5 mm. Capacitances from 3300 pF to 1.0 mF. Rated Voltages from 63 VDC to 400 VDC. Special Features Electrical Data High volume/capacitance ratio Capacitance range: Dissipation factors at + 20) C: tan d and reduced base 3300 pF to 1.0 mF (E12-values on request) at f C 0.1 mF 0.1 mF P C 1.0 mF PCM 2.5 mm Rated voltages: -3 -3 1 kHz 8 x 10 8 x 10 Self-healing 63 VDC, 100 VDC, 250 VDC, 400 VDC -3 -3 10 kHz 15 x 10 15 x 10 According to RoHS 2011/65/EU Capacitance tolerances: -3 100 kHz 30 x 10 20%, 10% (5% available subject to special enquiry) Voltage derating: Typical Applications Operating temperature range: A voltage derating factor of 1.25 % per K 55+ C to +105+ C must be applied from +85+ C for DC For general DC-applications e.g. Test specifications: voltages and from +75+ C for AC By-pass In accordance with IEC 60384-2 voltages. Blocking Climatic test category: Reliability: Coupling and decoupling 55/100/21 in accordance with IEC Operational life 300 000 hours Timing Insulation resistance at +20+ C: Failure rate P 2 fit (0.5 x U and 40) C) r Construction U U C 0.33 mF 0.33 mF < C 1.0 mF) r test 3 63 VDC 50 V 3.75 x 10 M 1250 sec (M x mF) Dielectric: Polyethylene-terephthalate (PET) film Capacitor electrodes: 4 100 VDC 100 V 1 x 10 M Vacuum-deposited Internal construction: Measuring time: 1 min. Test voltage: 1.6 U , 2 sec. r Maximum pulse rise time: Plastic film Capacitance Vacuum-deposited max. pulse rise time V/msec electrode pF/mF Metal contact layer (schoopage) 3300 ... 6800 100 Terminating wire 0.01 ... 0.022 50 0.033 ... 0.068 30 0.1 ... 0.33 20 0.47 ... 1.0 15 Encapsulation: Solvent-resistant, flame-retardant plastic case with epoxy resin seal, UL 94 V-0 Mechanical Tests Packing Terminations: Tinned wire. Pull test on pins: Available taped and reeled. Marking: 10 N in direction of pins according to Colour: Red. Marking: Silver. IEC 60068-2-21 Detailed taping information and graphs Vibration: at the end of the catalogue. 6 hours at 10 ... 2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: 2 4000 bumps at 390 m/sec in For further details and graphs please accordance with IEC 60068-2-29 refer to Technical Information. 29 06.21D WIMA MKS 02WIMA MKS 02 Continuation General Data 63 VDC/40 VAC* 100 VDC/63 VAC* Capacitance W H L PCM** Part number W H L PCM** Part number 0.01 mF 2.5 7 4.6 2.5 MKS0C021000B00 2.5 7 4.6 2.5 MKS0D021000B00 0.015 2.5 7 4.6 2.5 MKS0C021500B00 2.5 7 4.6 2.5 MKS0D021500B00 0.022 2.5 7 4.6 2.5 MKS0C022200B00 2.5 7 4.6 2.5 MKS0D022200B00 0.033 2.5 7 4.6 2.5 MKS0C023300B00 2.5 7 4.6 2.5 MKS0D023300B00 0.047 2.5 7 4.6 2.5 MKS0C024700B00 2.5 7 4.6 2.5 MKS0D024700B00 0.068 2.5 7 4.6 2.5 MKS0C026800B00 2.5 7 4.6 2.5 MKS0D026800B00 0.1 mF 3 7.5 4.6 2.5 MKS0C031000C00 3 7.5 4.6 2.5 MKS0D031000C00 0.15 3 7.5 4.6 2.5 MKS0C031500C00 3.8 8.5 4.6 2.5 MKS0D031500D00 0.22 3 7.5 4.6 2.5 MKS0C032200C00 4.6 9 4.6 2.5 MKS0D032200E00 0.33 3.8 8.5 4.6 2.5 MKS0C033300D00 5.5 10 4.6 2.5 MKS0D033300F00 0.47 4.6 9 4.6 2.5 MKS0C034700E00 0.68 5.5 10 4.6 2.5 MKS0C036800F00 1.0 mF 5.5 10 4.6 2.5 MKS0C041000F00 250 VDC/160 VAC* 400 VDC/200 VAC* Capacitance W H L PCM** Part number W H L PCM** Part number 3300 pF 2.5 7 4.6 2.5 MKS0F013300B00 2.5 7 4.6 2.5 MKS0G013300B00 4700 2.5 7 4.6 2.5 MKS0F014700B00 2.5 7 4.6 2.5 MKS0G014700B00 6800 2.5 7 4.6 2.5 MKS0F016800B00 2.5 7 4.6 2.5 MKS0G016800B00 0.01 mF 2.5 7 4.6 2.5 MKS0F021000B00 3 7.5 4.6 2.5 MKS0G021000C00 0.015 2.5 7 4.6 2.5 MKS0F021500B00 3.8 8.5 4.6 2.5 MKS0G021500D00 0.022 2.5 7 4.6 2.5 MKS0F022200B00 4.6 9 4.6 2.5 MKS0G022200E00 0.033 3 7.5 4.6 2.5 MKS0F023300C00 5.5 10 4.6 2.5 MKS0G023300F00 0.047 3.8 8.5 4.6 2.5 MKS0F024700D00 5.5 10 4.6 2.5 MKS0G024700F00 0.068 4.6 9 4.6 2.5 MKS0F026800E00 0.1 mF 5.5 10 4.6 2.5 MKS0F031000F00 * AC voltage: f = 50 Hz 1.4 x U + UDC U rms r ** PCM = Printed circuit module = pin spacing Dims. in mm. Part number completion: Tolerance: 20 % = M L W 10 % = K 5 % = J H d = 0.4 l Packing: bulk = S Pin length: 6-2 = SD 6 -2 d Taped version see page 161. 2.5 PCM at the pin exit points (0 .5) Impedance change with frequency (general guide). Rights reserved to amend design data without prior notification. 30 06.21