D WIMA MKP-X2 R Metallized Polypropylene (PP) RFI-Capacitors Class X2 with Internal Series Connection PCM 15 mm to 48.5 mm Special Features Electrical Data Reliable self-healing Capacitance range: Test specifications: Increased corona inception level 0.033 mF to 10 mF (E12-values on request) In accordance with IEC 60384-14 due to internal series connection Rated voltage: Maximum pulse rise time: High degree of interference 400 VAC 100 V/msec for pulses equal to a voltage suppression due to good Continuous DC voltage* (general guide): amplitude with 2 x 400 VAC = 565 V attenuation and low ESR T 1000 V according to IEC 60384-14 According to RoHS 2011/65/EU Capacitance tolerances: Test voltage: 20%, 10% (5% available subject C T 1.0 mF: 2260 VDC, 2sec. to special enquiry) C 1.0 mF: 1800 VDC, 2sec. Typical Applications Operating temperature range: Reliability: 55+ C to +105+ C Operational life 300 000 hours Class X2 RFI applications to meet Climatic test category: Failure rate 2 fit (0.5 x U and 40) C) EMC regulations r 55/105/56 in accordance with IEC Capacitors connected to the mains Passive flammability class: between phase and neutral or 3 B for capacitors with V 1750 mm phase conductors 3 C for capacitors with V T 1750 mm General requirements, pulse peak Insulation resistance at +20+ C: voltage T 2.5 kV 3 C T 0.33 mF: 15 x10 M As capacitor voltage divider in appli- C 0.33 mF: 5 000 sec (M x mF) cations requiring a high capacitance Measuring voltage: 100 V/1 min. stability over time Dissipation factors at +20 C: tan d Construction at f C T 0.1 mF 0.1 mF < C T 1.0 mF C > 1.0 mF -4 -4 -4 1 kHz T 4 x 10 T 5 x 10 T 10 x 10 Dielectric: -4 -4 10 kHz T 6 x 10 T 8 x 10 Polypropylene (PP) film -4 100 kHz T 25 x 10 Capacitor electrodes: Vacuum-deposited Internal construction: Mechanical Tests Packing Pull test on pins: Available taped and reeled up to and Dielectric 10 N in direction of pins including case size 15 x 26 x 31.5 / Vacuum-deposited electrode according to IEC 60068-2-21 PCM 27.5 mm. Metal contact layer (schoopage) Vibration: Terminating wire 6 hours at 10 ... 2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Detailed taping information and graphs Low air density: at the end of the catalogue. 1kPa = 10 mbar in accordance with Encapsulation: IEC 60068-2-13 Solvent-resistant, flame-retardant plastic Bump test: case with epoxy resin seal, UL 94 V0 2 4000 bumps at 390 m/sec in For further details and graphs please Terminations: accordance with IEC 60068-2-29 refer to Technical Information. Tinned wire. Marking: * The permissible pulse rise time du/dt (F ) max. Colour: Red. Marking: Black. will be subject to a reduction according to F = F x 2 x UAC / UDC max. r if the DC operating voltage UDC is higher than 2 x UAC 79 02.15 D WIMA MKP-X2 R Continuation General Data 400 VAC* Capacitance W H L PCM** Part number 0.033 mF 5 11 18 15 MKXR3W23304B00 0.047 5 11 18 15 MKXR3W24704B00 0.068 6 12.5 18 15 MKXR3W26804C00 0.1 mF 8 15 18 15 MKXR3W31004F00 6 15 26.5 22.5 MKXR3W31005B00 0.15 9 16 18 15 MKXR3W31504J00 7 16.5 26.5 22.5 MKXR3W31505D00 0.22 8.5 18.5 26.5 22.5 MKXR3W32205F00 0.33 10.5 19 26.5 22.5 MKXR3W33305G00 0.47 11 21 26.5 22.5 MKXR3W34705I00 0.68 13 24 31.5 27.5 MKXR3W36806D00 * f = 50/60 Hz ** PCM = Printed circuit module = pin spacing Dims. in mm. Part number completion: Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Pin length: 6-2 = SD d = 0.8 P Taped version see page 140. Rights reserved to amend design data without prior notification. Continuation page 81 80 02.15