xppower.com 200 Watts PBM200 Series Worldwide Medical Approvals Single, Dual, Triple and Quad Outputs Power Fail Detect Remote On/Off U Channel and Enclosed Versions 100 Watt Convection cooled Rating 3 Year Warranty Specification Input General Input Voltage 90-264 VAC Efficiency 80% maximum Input Frequency 47-63 Hz Isolation 4000 VAC Input to Output 1500 VAC Input to Ground Input Current 3.2 A rms at 115 VAC, 500 VAC Output to Ground 1.6 A rms at 230 VAC Switching Frequency 100 kHz 12 kHz Inrush Current 20 A at 115 VAC, 40 A at 230 VAC cold start 25 C Signals Power fail detect, remote on/off 3 Power Factor 0.98 typical Power Density 4.76 W/In Earth Leakage Current 90 A max at 115 VAC/60 Hz Power Fail Detect AC OK = TTL logic high 150 A max at 230 VAC/50 Hz AC not OK = TTL logic low Input Protection Internal T4 A/250 V in line and neutral MTBF 350 kHrs to MIL-HDBK-217F at +25 C, GB Output Environmental Output Voltage See table Operating Temperature 0 C to +70 C, derate linearly from 100% Output Voltage Trim Not user-adjustable power at +50 C to 50% power at +70 C Initial Set Accuracy 2% Cooling C versions have internal fan, Minimum Load See table & note 5 B versions are derated with convection Start Up Delay 2 s max cooling or require 25 CFM (see note 4) Start Up Rise Time 18 ms typical Operating Humidity Up to 95% RH, non-condensing Hold Up Time 20 ms minimum at full load & 110 VAC Storage Temperature -40 C to +85 C Drift 0.2% Operating Altitude 2500 m Line Regulation 0.5% max Shock Half sine pulse. acceleration 50 g, 11 ms Load Regulation See note 7 duration, 3 shocks in each direction, unpackaged, non-operating Transient Response 4% max deviation, recovery to within 1% in 500 s for a 25% load change Vibration Sinusoidal 10-55 Hz, amplitude 0.15 mm, 30 min/axis, unpackaged, non-operating Ripple & Noise 2% max pk-pk, 20 MHz bandwidth with a 22 F electrolytic & a 0.47 F tantalum capacitor EMC & Safety Overvoltage Protection 112-140% Vnom output 1 only, recycle Emissions EN55011 & FCC Class B conducted input to reset & radiated Overtemperature Shutdown at +85 C (singles) or +105 C Harmonic Currents EN61000-3-2, Class A Protection (multi outputs) with auto recovery, Voltage Flicker EN61000-3-3 measured internally ESD Immunity EN61000-4-2, level 3 Perf Criteria A Overload Protection 110-150% typical, auto recovery Radiated Immunity EN61000-4-3, level 3 Perf Criteria A Short Circuit Protection Trip and restart (Hiccup mode) EFT/Burst EN61000-4-4, level 3 Perf Criteria A Temperature 0.04%/C Coefficient Surge EN61000-4-5, level 3 Perf Criteria A Remote Sense Single output models only. Conducted Immunity EN61000-4-6 3 V, Perf Criteria A Compensates for up to 0.5 V drop Dips & Interruptions EN61000-4-11, 30% 10 ms, Remote On/Off On = Logic low or open circuit 60% 100 ms, >95% 5000 ms, Off = Logic high Perf Criteria A, B, B Safety Approvals EN60601-1, UL60601-1, CSA22.2 No. 601-1 per cUL AC DCAC DC PBM200 Models and Ratings (8) (2,5) (5) (3,5) Output 1 Output 2 Output 3 Output 4 Output Model (4) (1) (5) (7) (7) (7) (7) Power Number Vnom Imin Imax Reg Vnom Imax Reg Vnom Imax Reg Vnom Imax Reg 150 W 3.3 V 3.0 A 46.0 A 3% PBM200PS3V3-C 175 W 5.1 V 3.0 A 35.0 A 2% PBM200PS05-C 200 W 12.0 V 1.2 A 16.7 A 2% PBM200PS12-C 200 W 15.0 V 1.0 A 13.4 A 2% PBM200PS15-C 200 W 24.0 V 0.6 A 8.4 A 2% PBM200PS24-C 200 W 30.0 V 0.5 A 6.7 A 2% PBM200PS30-C 200 W 48.0 V 0.5 A 4.2 A 2% PBM200PS48-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% PBM200PD01-C 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% PBM200PD02-C 200 W +5.1 V 3.0 A 30.0 A 2% +24 V 4.0 A 4% PBM200PD03-C 200 W +12.0 V 1.0 A 8.7 A 2% +24 V 4.0 A 4% PBM200PD04-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -5 V 6.0 A 4% PBM200PT01-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -12 V 4.0 A 4% PBM200PT02-C 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -15 V 4.0 A 4% PBM200PT03-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% F 24 V 4.0 A 4% PBM200PT04-C 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -12 V 4.0 A 4% PBM200PT05-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -12 V 4.0 A 4% F 5 V 6.0 A 4% PBM200PQ01-C 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -15 V 4.0 A 4% F 24 V 4.0 A 4% PBM200PQ02-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -12 V 4.0 A 4% F 12 V 4.0 A 4% PBM200PQ03-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -15 V 4.0 A 4% F 15 V 4.0 A 4% PBM200PQ04-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -12 V 4.0 A 4% F 24 V 4.0 A 4% PBM200PQ05-C 175 W +3.3 V 3.0 A 30.0 A 3% +5.1 V 8.0 A 4% -12 V 4.0 A 4% F 12 V 4.0 A 4% PBM200PQ06-C Notes 1. For U-bracket format, replace suffix -C with suffix -B. 5. Zero minimum load for outputs 2, 3 & 4. 10% minimum load required on 2. Output 2 peak current is 12 A on +12 V, 9 A on +15 V, and 6 A on +24 V. output 1 for all outputs to meet regulation. Maximum 2 s duration with total load <200 W. 6. When the Remote Sense facility is not used, +Sense must be connected to 3. Output 4 is floating and can be connected externally for positive or negative +V, and Sense to return, on P2 connector. output. 7. Total regulation includes initial tolerance, line regulation and load regulation. 4. 200 W for -C version with a cover and fan assembly. 100 W for -B version 8. Peak current for single output models is 110% of Imax. Maximum 2 s duration with convection cooling (maximum current of output 1 & 2 derated with 10% duty cycle. to 50%). 200 W for -B version with 25 CFM forced air provided by user. Mechanical Details Model Number(s) B: Mounting holes. Threaded inserts for 6.32 screws (8 places) PTXX PSXX PDXX PT04 PQXX A: Mounting holes. Threaded inserts for M3 0.5 screws (8 places) (except 04) Conn Pin 1 -SENSE OP1 OP1 OP1 OP1 B 2 Return OP1 OP1 OP1 OP1 B 3 Return Com Ret Com Ret Com Ret Com Ret A A 4 Return Com Ret Com Ret Com Ret Com Ret 1.00 P2 5 Return Com Ret Com Ret Com Ret Com Ret (25.4) 6 OP1 OP2 OP2 OP2 OP2 0.50 7 OP1 N.C. OP3 N.C. OP3 6.00 (152.4) (12.7) 8 OP1 N.C. N.C. OP4 Ret OP4 Ret 9 +SENSE N.C. N.C. OP4 OP4 A 1 Fan A 1 B 2 Com Ret P3 B P2 P4 3 Com Ret 1 4 PFD PFD PFD PFD PFD P3 3.00 1 (76.2) 4.00 Notes (101.6) 2.30 P5 P1 1 1. Dimensions shown in inches (mm). (58.4) 2. Tolerance 0.02 0.5 maximum. L 3. Input connector P1 is Dinkle DT-35-B01W-03, output connector B N B P2 is Dinkle DT-35-B01W-09 screws are M3, Nickel plated. 9 G 4. Connector P3 mates with Molex housing 22-01-1043 & Molex A A 40445 series crimp terminal. 5. Connectors P4 & P5 mate with Molex housing 22-01-1023 & 0.50 0.85 (12.7) (21.6) Molex 40445 series crimp terminal. 6. P4 is for DC fan rated at 24 V/0.2 A (models PBM200PD03 & PD04), 5 V/0.38 A (PBM200PQ06), or 12 V/0.2 A (all other A A 1.50 models). Pin 1 Fan+, pin 2 Fan-. (38.1) 1.00 7. P5 is for Remote On/Off. Pin 1 is positive, pin 2 is return. B B (25.4) 0.65 8. Weight:1.83 lb (0.82kg) approx. for -B version, 2.14 lb (0.96kg) (16.5) approx. for -C version. 9. Maximum mounting screw length from surface of chassis 7.00 (177.8) is 0.17 inch (4.3 mm) 06-May-09