DC-HVDC Converter Q Series 1/2 Watt Output voltages from 100VDC to 10,000VDC xxx Series Output Proportional to Input 0.7VDC Turn-on Voltage Wide Operating Temperature Range Short Circuit Protection Low Ripple <1% 500VDC Input to Output Isolation No minimum load 3 Year Warranty Dimensions: Q01 - Q50: The Q Series is a broad line of ultra-miniature, high reliability DC to HV DC converters supplying 0.5 x 0.5 x 0.5 (12.7 x 12.7 x 12.7mm) up to 5,000 volts in only 0.125 cubic inches and up to 10,000 volts in only 0.614 cubic inches. Q60 - Q80: Input voltage can be 5V, 12V, 15V, or 24V. The output is directly proportional to the input voltage 0.85 x 0.85 x 0.85 (21.6 x 21.6 x 21.6mm) and is linear from <0.7V input to maximum input voltage, allowing for an adjustable output voltage. Output is load dependent. Isolation permits <500V bias on output return and output Key Applications: power is 0.5 watt. Avalanche Photo Diodes Photo Multiplier Tubes Piezo Devices No external components or minimum load are required. Variations include dual output (center- Sustaining Ion Pumps tap), a separate control pin, and an external shield. These component-sized converters operate Electrophoresis over a wide temperature range making them ideal for portable, battery-powered equipment Igniters requiring minimal size and weight. Capacitor Charging Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage 0.7 5,12,15,24 VDC See Models and Ratings Table. Input Current 400 mA See Models and Ratings Table. Control Voltage Input (optional) Analog Control Voltage adjusts output from 0 to 100%, not to exceed Input Voltage, see Application Notes. Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 10,000 VDC See Models and Ratings Table Output Current 5 mA See Models and Ratings Table Output Voltage Tolerance +10, -10 % At Max Vout, Full Load, Measured from pin 3 to pin 4 Minimum Load No minimum load required Regulation Unregulated, Output is proportional to Input. See Application Notes. Short Circuit Protection 1 minute Ripple and Noise 0.1 1% See Models and Ratings Table. Notes 1. Maximum output current is available at maximum rated output voltage, and 4. Proper thermal management techniques are required to maintain safe case derates linearly as input voltage is decreased. temperature at maximum power output. 2. Output Voltage is load dependent. Under light or no-load conditions, reduce 5. See Application Notes for connection diagrams, page 8. the Input Voltage so maximum rated Output Voltage is not exceeded. 6. All orderable part numbers are listed on pages 3 and 4. 3. Specifications are after 30 minute warm-up, full-load at 25C, unless otherwise noted. www.xppower.com 1DC-HVDC Converter Q Series Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature (case) -25 +70 C Q01 to Q20, standard operating temp Operating Temperature (case) -55 +75 C Q01 to Q20, extended operating temp Operating Temperature (case) -25 +60 C Q25 to Q50, standard operating temp Operating Temperature (case) -55 +70 C Q25 to Q50, extended operating temp Operating Temperature (case) -10 +60 C Q60 to Q101, standard operating temp Storage Temperature -55 +105 C Q01 to Q50 Storage Temperature -20 +105 C Q60 to Q101 Humidity 95 %RH Non-condensing Cooling Natural Convection Safety Approvals Safety Agency Safety Standard Notes & Conditions UL and TUV IEC/UL/CSA/EN 62368 CE CE Directive, RoHs and LVD Where applicable RoHS RoHS 2 and 3 Directive (2011/65/EU) Where applicable General Characteristic Minimum Typical Maximum Units Notes & Conditions Isolation: Input to Output 500 V < 500 VDC Bias on Output Return Leakage Current 250 nA Switching Frequency 75 500 kHz Construction Solid vacuum encapsulation, UL 94 V-0 rated. Mean Time Between Failure 3 MHrs Per Bellcore TR 332 Copper Shield Placement Block Diagram www.xppower.com 2