7.0mm x 5.0mm F O7L S LVDS Oscillator (Former F4700, F4710 Series) Features LVDS Output Stabilities to 20 PPM Temperature Ranges as wide as -40C to +85C Supply Voltages: 2.5V, 3.3V 2.5V ELECTRICAL CHARACTERISTICS PARAMETERS MAX (Unless otherwise noted) Frequency (F ) 25.0 ~ 400.0 MHz O Storage Temperature Range (T ) -55 ~ +125C STG Supply Voltage (V ) 2.5V10% 3.3V10% DD Input Current (I ) 63 mA DD Standby Current 30 A Output Symmetry (50% V ) 45% ~ 55% P-P Rise Time (20%~80% V ) 0.5 nS P-P Fall Time (80%~20% V ) 0.5 nS P-P Differential Output Voltage (V ) 0.247V ~ 0.454V OD Differential Offset Voltage (V ) 1.125V ~ 1.375V OS Output Termination 100 Ohms Typical Start-up Time (T ) 10 mS S 1 Output Disable Time 200 nS 1 Output Enable Time 10 mS Aging (per year 25C) 3 PPM Phase Jitter (12kHz~20MHz) 1 pS ENABLE / DISABLE FUNCTION 1 Pin Out 1 (pin 4), Out 2 (pin 5) 1 OPEN Active Active 1 Level V 70%V IH DD High Z 0 Level V 30%V IL DD Available Options by Stability & Operating Temp for 2.5V 2 Frequency Stability Operating Temperature (C) Frequency Range (MHz) 2 100PPM -10 ~ +70 25.0 ~ 400.0 2 100PPM -40 ~ +85 25.0 ~ 400.0 2 100PPM -40 ~ +105 25.0 ~ 300.0 2 50PPM -10 ~ +70 25.0 ~ 400.0 2 50PPM -40 ~ +85 25.0 ~ 400.0 2 50PPM -40 ~ +105 25.0 ~ 300.0 2 25PPM -10 ~ +70 25.0 ~ 400.0 3 25PPM -40 ~ +85 25.0 ~ 400.0 3 20PPM -10 ~ +70 25.0 ~ 400.0 1 An internal pull-up resistor from pin 1 to pin 6 allows active output if pin 1 is left open 2 Inclusive of 25C tolerance, operating temperature range, input voltage change, load change, Vibration, reflow, and one-year aging, shock, and vibration. 3 Inclusive of 25C tolerance and operating temperature range. Revised A: 05/05/2020 Page 1 of 3 www.foxonline.com 7.0mm x 5.0mm F O7L S LVDS Oscillator (Former F4700, F4710 Series) DIMENSIONS / MECHANICAL SPECIFICATIONS Note: *A 0.01F capacitor should be placed between VDD (Pin 4) and GND (Pin2) to minimize power supply line noise. *Dimensional drawing is for reference to critical specifications defined by size measurements. certain non-critical visual attributes, such as side castellations, reference pin shape, etc. may vary STANDARD SPECIFICATIONS PARAMETERS MAX (Unless otherwise noted) Maximum Soldering Temp / Time 260C / 10 Seconds x 2 Moisture Sensitivity Level (MSL) per J-STD-033 1 Termination Finish Au (0.3~1m) over Ni (1.27~8.89m) Seal Method Seam Lead (Pb) Free Yes RoHS Compliant Yes, no exemptions REACH Compliant Yes Revised A: 05/05/2020 Page 2 of 3 www.foxonline.com