F E D C B A ( 5 : 1 ) AT ALL TIMES WATER RESISTANT n1,12 (15x) CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. SEALING COMPOUND D D 0,3 + b 39,22 - 0,15 +0,13 33,32 - 0,12 +0,23 25,14 POS. 1 - 0,02 SEALING GASKET POS. 9 +0,25 8,23 - 0 RUBBER GASKET PLACED b ON TOP SURFACE OF MALE INSULATOR C C 15-00625o CONEC ABC 4-40 UNC SEE NOTE 13 SW 4,8 4-40 UNC B B NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK 6. SEALING GASKET: SILICONE 70 SHORE A BLUE 7. RUBBER GASKET: TPE BLACK 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 9. CONTACTS: COPPER ALLOY PLATING (SEE PART-NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 13. CONNECTOR IS PART MARKED: 15-00625o CONEC ABC (see note 9) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 10.09.2014 Lehmenkhler D-SUB MALE appd. 26.01.2015 Fischer 15pos. SOLDER CUP norm with closed 4-40 UNC thread dwg no: d-old DIN- 2 x b 5817 15.09.15 M.H. A3 R 15K1A1534 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00625o (see note 9) F E D C B A 10 0,3 + 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,4 + 10,66 - 0,3 0,25 + 2,55 - 0 +0,12 5,64 - 0,18R3,4 0,13 F E D C B A D D Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT 28,8 0,1 i 0,26 A B B B i 0,26 B 0,1 33,32 A scale: 5:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 10.09.2014 Lehmenkhler RECOMMENDED PANEL CUT-OUT appd. 26.01.2015 Fischer D-SUB MALE 15pos. SOLDER CUP norm with closed 4-40 UNC thread dwg no: d-old DIN- A3 R 15K1A1534 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 0,05 (2x) n3,1 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 11,4 0,1