Technical Data 11192 Effective November 2020 EXL1V0606 High current molded inductor Applications Voltage Regulator Module (VRM) Multi-phase regulators Point-of-load (POL) converters Desktop and server VRMs and EVRDs Base station equipment Battery power systems Graphics cards Product features Data networking and storage system High current carrying capacity Low DCR, high efficiency Environmental compliance and general specifications Magnetically shielded, low EMI Soft saturation Storage temperature range (Component): -40 C to +125 C Inductance range from 1 H to 10 H Operating temperature range: -40 C to +125 C Current range from 7.0 A to 19 A (ambient plus self-temperature rise) 7.4 mm x 7.1 mm footprint surface mount Solder reflow temperature: package in a 6.0 mm height J-STD-020 (latest revision) compliant Alloy powder core material HALOGEN Moisture Sensitivity Level (MSL) 1 HF Pb FREEEXL1V0606 Technical Data 11192 Effective November 2020 High current molded inductor Product specifications 3 4 I (A) typical I 1 2 rms sat OCL FLL (H) DCR (m) DCR (m) SRF (MHz) 5 Part number (H) 20% minimum +20 C rise +40 C rise (A) typical +25 C maximum +25 C typical EXL1V0606-1R0-R 1.0 0.56 15 19 16 3.9 4.29 37 EXL1V0606-1R5-R 1.5 0.84 13 16 14 5.1 5.61 31 EXL1V0606-2R2-R 2.2 1.23 11 14 12 7.0 7.80 26 EXL1V0606-3R3-R 3.3 1.84 9.0 12 10.5 11 12.1 24 EXL1V0606-4R7-R 4.7 2.63 8.0 11 9.5 13.1 14.4 22 EXL1V0606-5R6-R 5.6 3.13 7.5 10 9.0 14.3 15.8 17 EXL1V0606-6R8-R 6.8 3.8 7.0 9.0 8.7 18.9 20.8 15 EXL1V0606-8R2-R 8.2 4.59 6.0 8.0 8.0 22.5 24.8 14 EXL1V0606-100-R 10 5.6 5.0 7.0 6.8 26.6 29.3 12 1. Open circuit inductance (OCL) Test parameters: 100 kHz, 0.1 V , 0.0 Adc, +25 C 4. I : Peak current for approximately 30% rolloff +25 C sat rms 2. Full load inductance (FLL) Test parameters: 100 kHz, 0.1 V , I , , +25 C 5. Part number definition: EXL1V0606-xxx-R rms sat 3. I : Heat rated current (I ) will cause the part temperature rise approximately T of 40 C. Circuit design, EXL1V0606 = Product code and size rms rms component, PCB trace size and thickness, airflow and other cooling provisions all affect the part temperature. Part xxx= inductance value in H, R= decimal point, temperature should be verified in the end application. The part temperature (ambient + temp rise) should not exceed If no R is present then third digit equals the number of zeros +125 C under worst case operating conditions. -R suffix = RoHS compliant 6. Rated operating voltage: 15 V typical Mechanical parameters, schematic, pad layout (mm) Recommended pad layout Schematic Figure 1. DCR test Part number A B C D E F EXL1V0606-xxx-R 2.6 0.25 7.2 0.2 6.9 0.2 5.8 0.2 5.3 0.3 1.4 0.2 Part marking: 0606, xxx= Inductance value in H (R= Decimal point, if no R is present then last digit equals number of zeros), yyyy= Lot code All soldering surfaces to be coplanar within 0.1 millimeters Tolerances are 0.3 millimeters unless stated otherwise Dimensions of recommended PCB layout are reference only. Pad layout tolerances are 0.1 millimeters unless stated otherwise Four terminal kelvin-clip recommended for DCR testing as shown in Figure 1. Traces or vias underneath the inductor is not recommended. 2 www.eaton.com/electronics