FTP-638MCL104 Fujitsu

INTERFACE BOARD FTP-608 SERIES FTP-628DCL/DSL SERIES n INTERFACE 1. Centronics interface (1) Connector (CN2) Connector part number : BM30B-SRDS-G-TF (JST) or equivalent Mating connector part number : SHDR-30V-S-B (JST) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 PRSTB I Data strobe 2 PRSTB-RET Connected to logic GND 3 PRDT0 I Data 0 4 PRDT0-RET Connected to logic GND 5 PRDT1 I Data 1 6 PRDT1-RET Connected to logic GND 7 PRDT2 I Data 2 8 PRDT2-RET Connected to logic GND 9 PRDT3 I Data 3 10 PRDT3-RET Connected to logic GND 11 PRDT4 I Data 4 12 PRDT4-RET Connected to logic GND 13 PRDT5 I Data 5 14 PRDT5-RET Connected to logic GND 15 PRDT6 I Data 6 16 PRDT6-RET Connected to logic GND 17 PRDT7 I Data 7 18 PRDT7-RET Connected to logic GND 19 ACKNLG O Data input acknowledge 20 ACKNLG-RET Connected to logic GND 21 BUSY O Busy 22 BUSY-RET Connected to logic GND 23 RINF2 O Printer status 2 24 INPRM-RET Connected to logic GND 25 SLCTIN I Printer select 26 INPRM I Reset 27 RINF1 O Printer status 1 28 RINF3 O Printer status 3 29 ATF I Paper feed request 30 GND Logic GND Notes: Symbol means a negative logic signal. RET signal is a return signal of the twisted pair cable. I or O means a signal direction from the interface board side. (4) Data input signal timing (3) Connector pin number PRDT0~7 BM30B-SRDS-G-TF (JST) t1 t3 PRSTB t2 BUSY t4 ACKNLG t5 Data set time :t1 0.5 m sec PRSTB pulse width :t2 0.5 m sec Data hold time :t3 0.5 m sec PRSTB to BUSY= H :t4 0.5 m sec ACKNLG pulse time :t5 5.0 m sec 1FTP-628DCL/DSL Series (5) Printer status signals E1rror status R2INF R3INF RINF 1t.Pwaperou Lho Hwig Lo 2d.Phapernearen Hhig Hwig Lo 3p.Hheadu Hwig Lwo Lo 4y.Hheadtemperatureabnormalit Hwig Lho Hig 5y.Hweadvoltageabnormalit Lho Hhig Hig 6y.Hhardwareabnormalit Hhig Hhig Hig 7y.Mwarkdetectionabnormalit Lwo Lwo Lo 8l.Nworma Lwo Lho Hig 2. RS-232C (1) Connector (CN3) Connector part number : B8B-ZR-SM3B-TF (J.S.T.) or equivalent Mating connector part number : ZHR-8 (J.S.T.) or equivalent (2) Connector pin assignment Nlo.SOignaI./ C.ontentsNo NloSOignaI./ContentsNo 1DRIR2eceivedata TOD Transmissiondata 3RDOT D4ataterminalready G-ND Signalground 5RDIS D6atasetready SILCTIN Printerselect 7MIINPRR8eset AITF Paperfeedrequest Notes: Symbol means a negative logic signal. I or O means a signal direction from the interface board side. n CONNECTOR PIN ASSIGNMENT 1. Connector for power supply (CN1) Part number : B6B-XH-A (J.S.T) or equivalent (board side) Nlo.SOignaI./C.ontentsNo NloSOignaI./ContentsNo 15+-VP2owersupplyforlogic G-ND Groundforpowersupply 3DG-NG4roundforhead/motor G-ND Groundforhead/motor 5dV-dP6owersupplyforheadmotor V-dd Powersupplyforheadmotor 2