CPC1972GSTR

CPC1972 AC Power Switch INTEGRATED CIRCUITS DIVISION Parameter Ratings Units Description Blocking Voltage 800 V The CPC1972 is an AC Solid State Switch using P Load Current 250 mA optical coupling with dual power silicon controlled rms rectifier (SCR) outputs to produce an alternative to On State Voltage Drop 3 V (at I = 250 mA ) rms L rms optocoupler and Triac circuits. The CPC1972 switches Operating Voltage 550 V rms are robust enough to provide a blocking voltage of up to 800V . In addition, tightly controlled zero P Features cross circuitry ensures switching of AC loads without the generation of transients. The input and output Load Current up to 250mA rms circuits are optically coupled to provide 3750V of 800V Blocking Voltage rms P isolation and noise immunity between the control and 5mA Sensitivity load circuits. As a result the CPC1972 is well suited Zero-Crossing Detection for industrial environments where electromagnetic DC Control, AC Output interference could disrupt the operation of Optically Isolated electromechanical relays. TTL and CMOS Compatible Low EMI and RFI Generation High Noise Immunity Approvals Machine Insertable, Wave Solderable UL Recognized Component: File E69938 Flammability Classification Rating of V-0 CSA Certified Component: Certificate 1172007 Applications Ordering Information Programmable Control Part Number Description Process Control CPC1972G 6-Pin DIP (50/Tube) Power Control Panels CPC1972GS 6-Pin Surface Mount (50/Tube) Remote Switching CPC1972GSTR 6-Pin Surface Mount (1000/Reel) Gas Pump Electronics Contactors Large Relays Solenoids Pin Configuration Motors Heaters 1 6 + LED AC Load 2 5 ZC LED N/C 3 4 AC Load N/C Pb e3 DS-CPC1972-R05 1 www.ixysic.comCPC1972 INTEGRATED CIRCUITS DIVISION Absolute Maximum Ratings 25C Absolute Maximum Ratings are stress ratings. Stresses in Parameter Ratings Units excess of these ratings can cause permanent damage to Blocking Voltage 800 V P the device. Functional operation of the device at conditions Reverse Input Voltage 5 V beyond those indicated in the operational sections of this Input Control Current 50 mA data sheet is not implied. Peak (10ms) 1 A 1 Input Power Dissipation 150 mW 2 Total Package Dissipation 800 mW Isolation Voltage, Input to Output 3750 V rms Operational Temperature -40 to +85 C Storage Temperature -40 to +125 C 1 Derate linearly 1.33 mW / C 2 Derate linearly 6.67 mW / C Electrical Characteristics 25C Parameters Conditions Symbol Min Typ Max Units Output Characteristics Operating Voltage Range - V 5 - 550 V L rms Load Current Continuous - I 5 - 250 mA L rms Peak t = 10ms I -- 2 A TSM P Off State Leakage Current V =800V I -- 1 A L P LEAK On-State Voltage Drop I = 250mA V -- 3 V L rms ON rms Critical Rate of Rise - dV/dt 500 - - V/s Holding Current I =5mA I - 300 - A F H Switching Speeds Turn-on t - - 0.5 on I =5mA cycles F Turn-off t - - 0.5 off 1 Zero-Cross Turn-On Voltage 1st half-cycle - - 5 20 V Subsequent half-cycle - - 1 - V Operating Frequency - - 20 - 500 Hz 2 Load Power Factor for Guaranteed Turn-On f=60Hz PF 0.25 - - - Input Characteristics 3 Input Control Current to Activate -I -- 5 mA F Input Voltage Drop I =5mA V 0.9 1.2 1.4 V F F Input Drop-out Voltage - - 0.8 - - V Reverse Input Current V =5V I - - 10 A R R Common Characteristics Input to Output Capacitance - C -3 - pF I/O 1 Zero Cross 1st half-cycle <100Hz 2 Snubber circuits may be required at low power factors. 3 For high noise environment use at least 10mA LED current R05 2 www.ixysic.com