ATmega16M1/32M1/32C1/64M1/64C1 Appendix A - Atmel ATmega16M1/ATmega32M1/ ATmega32C1/ATmega64M1/ATmega64C1 Automotive Specification at 150C DATASHEET Description This document contains information specific to devices operating at temperatures up to 150C. Only deviations are covered in this appendix, all other information can be found in the complete Automotive datasheet. The complete Automotive datasheet can be found on 1. Electrical Characteristics 1.1 Absolute Maximum Ratings Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Test Conditions Unit Operating temperature 55 to +150 C Storage temperature 65 to +175 C Voltage on any pin except RESET with respect to ground 0.5 to V +0.5 V CC Voltage on RESET with respect to ground 0.5 to +13.0 V Maximum operating voltage 6.0 V DC current per I/O pin 30 mA DC current V and GND 200.0 CC 1.2 DC Characteristics T = 40C to +150C, V = 4.5V to 5.5V (unless otherwise noted) A CC Parameters Test Conditions Symbol Min. Typ. Max. Unit Input low voltage, (1) except XTAL1 and V = 4.5V to 5.5V V 0.5 +0.2V V CC IL CC RESET pin Input high voltage, (2) except XTAL1 and V = 4.5V to 5.5V V 0.6V V + 0.5 V CC IH CC CC RESET pins Input low voltage, (1) V = 4.5V to 5.5V V 0.5 +0.1V V CC IL1 CC XTAL1 pin Input high voltage, (2) V = 4.5V to 5.5V V 0.8V V + 0.5 V CC IH1 CC CC XTAL1 pin Input low voltage, (1) V = 4.5V to 5.5V V 0.5 +0.2V V CC IL2 CC RESET pin Input high voltage, (2) V = 4.5V to 5.5V V 0.9V V + 0.5 V CC IH2 CC CC RESET pin Input low voltage, (1) V = 4.5V to 5.5V V 0.5 +0.2V V CC IL3 CC RESET pin as I/O Input high voltage, (2) V = 4.5V to 5.5V V 0.8V V + 0.5 V CC IH3 CC CC RESET pin as I/O Notes: 1. Max means the highest value where the pin is guaranteed to be read as low 2. Min means the lowest value where the pin is guaranteed to be read as high 3. Although each I/O port can sink more than the test conditions (20mA at V = 5V) under steady state conditions (non- CC transient), the following must be observed: 1 The sum of all IOL, for all ports, should not exceed 400mA. 2 The sum of all IOL, for ports C0 - C5, should not exceed 200mA. 3 The sum of all IOL, for ports C6, D0 - D4, should not exceed 300mA. 4 The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 300mA. If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test condition. 4. For temperature range +125C to +150C only. For 40C to +125C, refer to ATmega16M1/ATmega16M1/32M1/32C1/64M1/64C1/ATA8888/ATmega64M1/ATmega64C1 Automotive datasheet. 2 ATmega16M1/32M1/32C1/64M1/64C1 Automotive DATASHEET 7781FAVR07/14