63852-9170 Molex

T2 Terminator for Male and Female Crimp Terminals T2 Terminator Tooling Specification Sheet Order No. 63852-9100 FEATURES It is ideally suited for mid-volume bench operations This terminator can be installed in the TM42 and the TM40 press or Base Unit adapter for 3BF press Quick punch removal with the push of a button for fast and easy tooling change Track adjustment capabilities in the T2 Terminators for improved control of the bell mouth size and cutoff tab length T2 Terminator has standardized tooling with the Molex FineAdjust Applicator which will reduce your inventory requirements SCOPE Products: Male and Female Crimp Terminals, 14-18 AWG. Insulation Diameter Terminal Terminal Wire Size Strip Length IPC/WHMA-A620 Terminal Maximum Series No. Order No. AWG mm mm In. mm In. mm In. 35745 35745-0210 14-18 2.00-0.80 2.80-3.40 .110-.134 3.40 .134 4.00-4.80 .157-.189 35746 35746-0210 14-18 2.00-0.80 2.80-3.40 .110-.134 3.40 .134 4.00-4.80 .157-.189 35747 35747-0210 14-18 2.00-0.80 2.80-3.40 .110-.134 3.40 .134 4.00-4.80 .157-.189 35748 35748-0210 14-18 2.00-0.80 2.80-3.40 .110-.134 3.40 .134 4.00-4.80 .157-.189 To achieve optimum IPC-A620 insulation crimps, use this insulation OD range. Overall insulation OD specification for terminal. DEFINITION OF TERMS BEND UP BELL MOUTH BRUSH SEAM INSULATION CRIMP ROLLING TWISTING STRIP BEND LENGTH DOWN CONDUCTOR CUT-OFF TAB CRIMP COND.CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc No: ATS-638529100 Release Date: 11-08-99 UNCONTROLLED COPY Page 1 of 6 Revision: C Revision Date: 11-05-08 T2 Terminator for Male and Female Crimp Terminals CRIMP SPECIFICATION Bell mouth Cut-off Tab Maximum Conductor Brush Terminal Series No. mm In. mm In. mm In. 35745 0.20-0.50 .008-.020 0.30 .012 0.30-0.80 .012-.032 35746 0.20-0.50 .008-.020 0.30 .012 0.30-0.80 .012-.032 35747 0.20-0.50 .008-.020 0.30 .012 0.30-0.80 .012-.032 35748 0.20-0.50 .008-.020 0.30 .012 0.30-0.80 .012-.032 Punch Width (Ref) Bend up Bend down Twist Roll Terminal Series No. Conductor Insulation Seam Degree Degree mm In mm In 35745 3 3 3 5 2.50 .098 3.40 .134 Seam shall not be open and no wire allowed out 35746 3 3 3 5 2.50 .098 3.40 .134 of the crimping area 35747 3 3 3 5 2.50 .098 3.40 .134 35748 3 3 3 5 2.50 .098 3.40 .134 After crimping, the conductor profile should measure the following. Wire Size Conductor Crimp Height Pull Force Minimum Terminal Series No. 2 AWG mm mm In. N Lb. 14 2.00 1.60-1.70 .063-.067 147.1 33.1 35745 16 1.30 1.50-1.60 .059-.063 127.6 28.7 18 0.80 1.40-1.50 .055-.059 97.8 22.0 14 2.00 1.60-1.70 .063-.067 147.1 33.1 35746 16 1.30 1.50-1.60 .059-.063 127.6 28.7 18 0.80 1.40-1.50 .055-.059 97.8 22.0 14 2.00 1.60-1.70 .063-.067 147.1 33.1 35747 16 1.30 1.50-1.60 .059-.063 127.6 28.7 18 0.80 1.40-1.50 .055-.059 97.8 22.0 14 2.00 1.60-1.70 .063-.067 147.1 33.1 35748 16 1.30 1.50-1.60 .059-.063 127.6 28.7 18 0.80 1.40-1.50 .055-.059 97.8 22.0 Pull Force should be measured with no influence from the insulation crimp. The above specifications are guidelines to an optimum crimp. Doc No: ATS-638529100 Release Date: 11-08-99 UNCONTROLLED COPY Page 2 of 6 Revision: C Revision Date: 11-05-08