MP2605DQ-LF-P Monolithic Power Systems

MP2605 28V, 1A Li-Ion/Li-Polymer Battery Charger with Trickle Charge and Timer The Future of Analog IC Technology DESCRIPTION FEATURES The MP2605 is a linear, high-performance Proprietary V Surge Protection up to 28V IN single cell Li-Ion/Li-Polymer battery charger. By Programmable Charge Current : integrating high voltage input protection into the 200mA to 1.0A charger IC, the MP2605 can tolerate an input Trickle Charge surge up to +28V. 40A Shutdown Current 7V Input OVP The device features constant current (CC) and Auto Recharge constant voltage (CV) charging modes with Charge-Timer programmable charge currents (200mA to 1A), current blocking, and trickle charge. The device Fault and Charge Status Indicators also provides fault and charge status APPLICATIONS indications to the system. Cell Phones For guaranteed safe operation, the MP2605 Digital Cameras reduces charge current when the device Smart Phones reaches high temperature (due to limited PCB PDAs space). Other safety features include battery MP3 Players temperature monitoring and programmable timer to complete the charging cycle. MPS and The Future of Analog IC Technology are Registered Trademarks of Monolithic Power Systems, Inc. The MP2605 is available in 10-pin 3mm x 3mm QFN packages. TYPICAL APPLICATION 3.5V - 6.5V V IN To system I BATT 1 10 IN BATT 9 2 NTC ACOK MP2605 3 8 CHG ISET V BATT 4 7 TMR SS 5 6 GND SHDN CSS ON OFF MP2605 Rev. 1.0 www.MonolithicPower.com 1 1/19/2017 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 2017 MPS. All Rights Reserved. MP2605 28V, 1A LINEAR BATTERY CHARGER WITH TRICKLE CHARGE AND TIMER ORDERING INFORMATION Part Number* Package Top Marking Free Air Temperature (T ) A QFN10 (3mm x 3mm) MP2605DQ U4YW -40 C to +85 C * For Tape & Reel, add suffix Z (e.g. MP2605DQZ). For RoHS Compliant packaging, add suffix LF (e.g. MP2605DQLFZ) PACKAGE REFERENCE 1 10 2 9 3 8 4 7 5 6 (1) (4) ABSOLUTE MAXIMUM RATINGS Thermal Resistance JA JC IN to GND ..................................... -0.3V to +28V 3x3 QFN10 .............................. 50 ...... 12 ... C/W ACOK and CHG Maximum Sink Current ..... 20mA Notes: All Other Pins to GND .................. -0.3V to +6.5V (2) 1) Exceeding these ratings may damage the device. Continuous Power Dissipation (T = +25C) A 2) The maximum allowable power dissipation is a function of the maximum junction temperature T (MAX), the junction-to- J ....2.5W ambient thermal resistance , and the ambient temperature JA Junction Temperature ............................... 140 C T . The maximum allowable continuous power dissipation at A any ambient temperature is calculated by P (MAX) = (T Lead Temperature .................................... 260 C D J (MAX)-T )/ . Exceeding the maximum allowable power A JA Storage Temperature ............... -65C to +150 C dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal (3) Recommended Operating Conditions shutdown circuitry protects the device from permanent damage. Nominal Supply Voltage V ............ 3.5V to 6.5V IN 3) The device is not guaranteed to function outside of its Operating Junct. Temp (T ) ...... -40C to +125 C J operating conditions. 4) Measured on JESD51-7, 4-layer PCB MP2605 Rev. 1.0 www.MonolithicPower.com 2 1/19/2017 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 2017 MPS. All Rights Reserved.