ALUMINUMELECTROLYTICCAPACITORS Chip Type, Low Impedance, Long Life Assurance CW series Chip type with load life of 7000 hours at +105C. Low impedance temperature range up to +105C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). Low Impedance CB CW Specifications Item Performance Characteristics Category Temperature Range 25 to +105C Voltage Range Rated 6.3 to 50V Rated Capacitance Range 10 to 470F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes application of rated voltage, leakage current is not more than 0.01 CV or 3 (A) , whichever is greater. Measurement frequency : 120Hz at 20C 6.3 10 16 25 35 50 Rated voltage (V) Tangent of loss angle (tan ) tan (MAX.) 0.32 0.28 0.26 0.16 0.14 0.14 Measurement frequency : 120Hz Rated voltage (V) 6.3 10 16 25 35 50 Stability at Low Temperature Impedance ratio Z25C / Z+20C 4 3 2 2 2 2 ZT / Z20 (MAX.) The specifications listed at right shall be met Capacitance change Within 30% of the initial capacitance value when the capacitors are restored to 20C tan 300% or less than the initial specified value Endurance after the rated voltage is applied for 7000 Leakage current Less than or equal to the initial specified value hours at 105C. After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within 10% of the initial capacitance value Resistance to soldering maintained at 250C. The capacitors shall meet the tan Less than or equal to the initial specified value heat characteristic requirements listed at right when they are Leakage current Less than or equal to the initial specified value removed from the plate and restored to 20C. Marking Black print on the case top. Chip Type Type numbering system (Example : 10V 150 F) Positive (5 to 6.3) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Plastic platform Voltage ( C : 16V ) U C W 1 A 1 5 1 M C L 1 G S Series 0.3MAX. C0.2 Taping code Configuration Capacitance tolerance (20%) D Code 5 6.3 CL Rated capacitance (150F) L0.3 8 10 NL Rated voltage (10V) Negative Capacitance Lot No. H Series name Type Positive (8 to 10 ) (mm) Plastic platform Voltage ( V : 35V ) D L 5 7 6.3 7 8 10 10 10 6.3 8.7 0.3MAX. Series C0.2 Trade mark A 2.1 2.4 2.4 2.9 3.2 B 5.3 6.6 6.6 8.3 10.3 C 5.3 6.6 6.6 8.3 10.3 E 1.3 2.2 2.2 3.1 4.5 L0.5 L 7.0 7.0 8.7 10 10 Negative Lot No. Capacitance H H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Pressure relief vent Voltage V 6.3 10 16 25 35 50 Code j A C E V H Dimension table in next page. CAT.8100D A2 A2 150C 220V CW CW D0.5 D0.5 B0.2 B0.2 0.5MAX. 0.5MAX. E E A0.2 A0.2 A0.2 A0.2ALUMINUMELECTROLYTICCAPACITORS CWseries Dimensions V 6.3 10 16 25 35 50 Cap. Code 0J 1A 1C 1E 1V 1H (F) 100 10 5 7 2.2 95 22 220 5 7 2.2 95 5 7 2.2 95 5 7 2.2 95 33 330 5 7 2.2 95 6.3 7 1.1 140 6.3 8.7 1.0 230 470 5 7 2.2 95 6.3 7 1.1 140 6.3 7 1.1 47 140 6.3 8.7 1.0 230 8 10 0.53 350 100 101 6.3 7 1.1 140 6.3 7 1.1 140 6.3 8.7 1.0 230 8 10 0.53 350 150 151 6.3 7 1.1 140 6.3 8.7 1.0 230 221 6.3 8.7 1.0 220 230 6.3 8.7 1.0 230 8 10 0.22 600 8 10 0.22 600 10 10 0.35 670 330 331 6.3 8.7 1.0 230 8 10 0.22 600 8 10 0.22 600 10 10 0.16 850 Case size Rated Impedance D L (mm) ripple 470 471 8 10 0.22 600 8 10 0.22 600 10 10 0.16 850 Max. impedance () at 20C 100kHz, Rated ripple current (mArms) at 105C 100kHz Frequency coefficient of rated ripple current Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more Coefficient 0.35 0.50 0.64 0.83 1.00 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D