ALUMINUMELECTROLYTICCAPACITORS Chip Type, Wide Temperature Range WT series Chip type operating over wide temperature range of to 55 to +105C. WZ Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. High Compliant to the RoHS directive (2011/65/EU). Temperature Reflow Low WF impeadance WT Long Life UT Smaller ZT Specifications Item Performance Characteristics Category Temperature Range 55 to +105C Rated Voltage Range 4 to 50V Rated Capacitance Range 0.1 to 1500F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes application of rated voltage, leakage current is not more than 0.01CV or 3 (A) , whichever is greater. Measurement frequency : 120Hz at 20C Rated voltage (V) 4 6.3 10 16 25 35 50 Tangent of loss angle (tan ) tan (MAX.) 0.40 0.30 0.24 0.20 0.16 0.14 0.14 Measurement frequency : 120Hz Rated voltage (V) 4 6.3 10 16 25 35 50 Stability at Low Temperature Z25C / Z+20C Impedance ratio 7 4 3 2 2 2 2 ZT / Z20 (MAX.) Z40C / Z+20C 15 8 8 4 4 3 3 Capacitance Within 25% of the initial capacitance value for capacitors of 3mm unit, and 16V or less. The specifications listed at right shall be change Within 20% of the initial capacitance value for capacitors of 25V or more. met when the capacitors are restored to Endurance 20C after the rated voltage is applied for tan 200% or less than the initial specified value 1000 hours at 105C. Leakage current Less than or equal to the initial specified value After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within 10% of the initial capacitance value Resistance to soldering is maintained at 250C. The capacitors shall meet the Less than or equal to the initial specified value tan heat characteristic requirements listed at right when they are Leakage current Less than or equal to the initial specified value removed from the plate and restored to 20C. Marking Black print on the case top. Chip Type Type numbering system (Example : 16V 10 F) (3 to 8 5.4 ) Positive (3 to 8 5.4 ) Positive D code 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Capacitance Plastic platform 1 D code 1 2 3 4 5 6 7 8 9 10 11 12 13 14 3 to 8 (5.4L) GB Capacitance Voltage Plastic platform0.3 MAX. C0.2 1 U W T 1 C 1 0 0 M C L 1 G B 105C Marking 3 to 8 (5.4L) GB 6.3 to 10 (L 5.8) GS Voltage 0.3 MAX. C0.2 U W T 1 C 1 0 0 M C L 1 G B 105C Marking Package code 6.3 to 10 (L 5.8) GS Size code Package code D code Configuration Size code 3 2 +0.1 D code Capacitance tolerance (20%) 2 L 0.2 D code 4 to 10 1 Configuration Lot No. Negative 3 to 8 (L 7.7) CL (L0.3) H 3 Rated capacitance (10F) 3 2 +0.1 8 to 10 (L = 10) NL D code Capacitance tolerance (20%) 2 3 Apply to 6.3 5.8, L 6.3 7.7 0.2 Rated voltage (16V) 4 to 10 1 Lot No. Negative 3 to 8 (L 7.7) CL (L0.3) 3 H Rated capacitance (10F) Series name 8 to 10 (L = 10) NL (8 10, 10 10 ) 3 Apply to 6.3 5.8, 6.3 7.7 Positive Rated voltage (16V) Type Capacitance Plastic platform 1 105C Marking Series name 0.3 MAX. C0.2 Voltage Trade mark(8 10, 10 10 ) Positive Type Capacitance (mm) Plastic platform 1 105C Marking D L 0.3 MAX. C0.2 Voltage 3 5.4 4 5.4 5 5.4 6.3 5.4 6.3 5.8 6.3 7.7 8 5.4 8 10 10 10 Trade mark L0.5 (mm) Lot No. A 1.5 1.8 2.1 2.4 2.4 2.4 3.3 2.9 3.2 Negative Pressure relief vent H D L B 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 3 5.4 4 5.4 5 5.4 6.3 5.4 6.3 5.8 6.3 7.7 8 5.4 8 10 10 10 1. Voltage mark for 6.3V is 6V . In case of marking for 3 units, V for rated C 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 voltage is omitted. L0.5 2. In case of marking for 3 units. Lot No is expressed by a digit (month code). Lot No. A 1.5 1.8 2.1 2.4 2.4 2.4 3.3 2.9 3.2 Negative Pressure relief vent E 0.8 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5 H B 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 L 5.4 5.4 5.4 5.4 5.8 7.7 5.4 10 10 1. Voltage mark for 6.3V is 6V . In case of marking for 3 units, V for rated H 0.5 to 0.8 0.5 to 0.8C 0.5 to 0.83.30.5 to 0.84.30.5 to 0.8 5.30.5 to 0.8 0.5 to 0.86.6 0.8 to 1.16.6 0.8 to 1.16.6 8.3 8.3 10.3 voltage is omitted. 2. In case of marking for 3 units. Lot No is expressed by a digit (month code). E 0.8 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5 L 5.4 5.4 5.4 5.4 5.8 7.7 5.4 10 10 Dimension table in next page. H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 CAT.8100D 2 2 A2P A2P 100 10 A2P A2P 35V 16V 100 10 35V 16V D0.5 D0.5 D0.5 D0.5 B0.2 B0.2 B0.2 B0.2 0.5 MAX. 0.5 MAX. E E A0.2 A0.2 A0.2 A0.2 0.5 MAX. 0.5 MAX. E E A0.2 A0.2 A0.2 A0.2ALUMINUMELECTROLYTICCAPACITORS WT series Dimensions V 4 6.3 10 16 25 35 50 Code Cap. (F) 0G 0J 1A 1C 1E 1V 1H 0.1 0R1 4 5.4 (3) 1.0 0.22 R22 4 5.4 (3) 2.6 0.33 R33 4 5.4 (3) 3.2 0.47 R47 4 5.4 (3) 3.8 1 010 4 5.4 (3) 6.3 (5.9) 2.2 2R2 3 5.4 7.5 4 5.4 (3) 11 (9) 3.3 9 3R3 3 5.4 4 5.4 14 4.7 15 4R7 4 5.4 (3) 13 (10) 4 5.4 5 5.4 19 10 100 4 5.4 (3) 18 (14) 5 5.4 23 5 5.4 25 6.3 5.4 30 22 42 220 4 5.4 22 4 5.4 22 5 5.4 27 5 5.4 30 6.3 5.4 38 6.3 5.4 8 5.4 51 (45) 33 59 (52) 330 5 5.4 30 5 5.4 30 5 5.4 35 6.3 5.4 40 6.3 5.4 48 8 5.4 6.3 7.7 60 47 470 5 5.4 36 5 5.4 36 6.3 5.4 46 6.3 5.4 50 8 5.4 66 (59) 6.3 5.8 63 6.3 7.7 63 100 84 101 6.3 5.4 60 6.3 5.4 60 6.3 5.4 60 6.3 5.4 60 6.3 7.7 91 6.3 7.7 8 10 140 150 155 151 6.3 5.8 86 6.3 5.8 86 6.3 5.8 86 6.3 7.7 95 8 10 140 8 10 10 10 180 220 221 8 5.4 102 (91) 8 5.4 102 (91) 6.3 7.7 105 6.3 7.7 105 8 10 155 8 10 190 10 10 220 330 300 331 6.3 7.7 105 6.3 7.7 105 8 10 195 8 10 195 8 10 190 10 10 470 471 8 10 210 8 10 210 8 10 210 8 10 230 10 10 300 680 681 8 10 210 8 10 210 10 10 310 10 10 310 1000 102 8 10 230 8 10 230 10 10 310 Case size Rated ripple D L (mm) 1500 152 10 10 310 10 10 310 Rated ripple current (mArms) at 105C 120Hz ( ) is also available with 3mm upon request. In such a case, 2 will be put at 12th digit of type numbering system. Size 6.3 5.8 is available for capacitors marked. In such a case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more Coefficient 0.70 1.00 1.17 1.36 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UX(p.154), UJ(p.160) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100D