D2JW Sealed Subminiature Basic Switch Ultra-small and Highly Sealed O Degree of protection conforms to JIS Waterproof standard and IEC IP67. (Excluding the terminals on terminal models) O Wide range of operating temperatures from 40C to +85C. D 2 O Gold-alloy crossbar contact and coil spring offer J long durability and high contact reliability. W RoHS Compliant Model Number Legend D2JW-01 1 2 3 1. Actuator 2. Contact form None : Pin plunger 1: SPDT K1A : Short hinge lever 2: SPST-NC (Molded lead wire models only) K1 : Hinge lever 3: SPST-NO (Molded lead wire models only) K2 : Hinge roller Lever 3. Terminals K3 : Simulated roller hinge lever None : Solder terminals -MD : Molded lead wires List of Models Actuator Terminals Contact form Model Solder terminals SPDT D2JW-011 SPDT D2JW-011-MD Pin plunger Molded lead SPST-NC D2JW-012-MD wires SPST-NO D2JW-013-MD Solder terminals SPDT D2JW-01K1A1 SPDT D2JW-01K1A1-MD Short hinge lever Molded lead SPST-NC D2JW-01K1A2-MD wires SPST-NO D2JW-01K1A3-MD Solder terminals SPDT D2JW-01K11 SPDT D2JW-01K11-MD Hinge Lever Models Molded lead SPST-NC D2JW-01K12-MD wires SPST-NO D2JW-01K13-MD Solder terminals SPDT D2JW-01K21 SPDT D2JW-01K21-MD Hinge Roller Lever Molded lead Models SPST-NC D2JW-01K22-MD wires SPST-NO D2JW-01K23-MD Solder terminals SPDT D2JW-01K31 SPDT D2JW-01K31-MD Simulated Roller Hinge Molded lead Lever Models SPST-NC D2JW-01K32-MD wires SPST-NO D2JW-01K33-MD Contact form O SPDT O SPST-NC O SPST-NO COM NO NC COM NC COM NO (Black) (Blue) (Red) (Black) (Red) (Black) (Blue) The color in parentheses indicates the color of the lead wire. 1D2JW Sealed Subminiature Basic Switch Contact Specifications Characteristics 1 mm to 250 mm/s Specification Crossbar Permissible operating speed (for pin plunger models) Material Gold alloy Permissible Mechanical 240 operations/min Contact operating Gap (standard Electrical 30 operations/min 0.5 mm frequency value) 100 M min. Insulation resistance NC 0.1A max. (at 500 VDC with insulation tester) Inrush current Contact Solder terminal models 100 m max. NO 0.1A max. resistance Minimum applicable load (see Molded lead wire models 140 m max. (initial value) 5 VDC 1 mA note) Between terminals of the same 600 VAC 50/60 Hz 1min polarity D Dielectric Between current-carrying metal 1,000 VAC 50/60 Hz 1min Ratings strength * 1 parts and ground 2 Between each terminal and J 1,000 VAC 50/60 Hz 1min non-current-carrying metal parts W Rated voltage Resistive load Vibration 10 to 55 Hz, 1.5 mm double Malfunction 30 VDC 0.1A resistance * 2 amplitude 2 Shock Durability 1,000 m/s approx. 100G max. Note. The above rating values apply under the following test conditions. 2 resistance Malfunction * 2 200 m/s approx. 20G max. (1) Ambient temperature: 202C 1,000,000 operations min. (2) Ambient humidity: 655% Mechanical (60 operations/min) (3) Operating frequency: 30 operations/min Durability * 3 100,000 operations min. Electrical (30 operations/min) IEC IP67 (excluding the terminals Degree of Solder terminal models on terminal models) protection Molded lead wire models IEC IP67 40C to +85C (at ambient Ambient operating temperature humidity of 60% max.) (with no icing or condensation) Ambient operating humidity 35% to 98% (for +5C to +35C) Approx. 0.6g (for pin plunger Weight models with terminals) Note. The data given above are initial values. *1. The dielectric strength values shown apply for use with Separator (refer to page 4). *2. For the pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, they apply at the total travel position. Close or open circuit of the contact is 1ms max. *3. For testing conditions, consult your OMRON sales representative. Mounting Holes (Unit: mm) M2.3 mounting screw hole 0.1 4.8 Dimensions (Unit: mm) /Operating Characteristics Dimensions and operating characteristics of other actuator models for lead wire models are omitted in the illustration below, as the dimensions other than the termial part and operatiing characteristics is common with Solder terminal models. O Pin plunger models 1.6 dia. PT D2JW-011 A Operating characteristics Operating Force OF Max. 2.45 N 250 gf OP Releasing Force RF Min. 0.98 N 100 gf 9.4 12.3 Pretravel PT Max. 0.6 mm 2.8 Overtravel OT Min. 0.3 mm +0.05 2.35 0.025 1.3 Movement Differential MD Max. 0.1 mm 0.5 0.4 +0.05 1 2.35 dia. Operating Position OP 8.10.3 mm 0.025 +0.05 2.5 dia. 2 0.025 0.1 5.3 3.95 4.80.05 3.95 3.95 12.7 1.8 7.95 O Short hinge lever models t0.3 Stainless-steel PT A lever D2JW-01K1A1 R11.5 3 Operating Force OF Max. 1.15 N 117 gf OP Releasing Force RF Min. 0.23 N 23 gf 6.15 9.4 Pretravel PT Max. 5.4 mm 12.3 Overtravel OT Min. 0.7 mm 2.8 Movement Differential MD Max. 0.5 mm +0.05 2.35 0.025 1.3 Operating Position OP 8.40.8 mm 0.5 0.4 +0.05 1 2.35 dia. 0.025 +0.05 2.5 dia. 2 0.025 0.1 5.3 0.05 4.8 3.95 3.95 3.95 12.7 Note 1. Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. Note 2. The operating characteristics are for operation in the A direction ( ). 2