EE-SPX402-W2A

Slot-type Photomicrosensor with Cable EE-SPX-W Photomicrosensor with built-in amplifier and attached cable reduces external light interference. Light modulation effectively reduces external light interference. Wide operation voltage range: 5 to 24 VDC Easy operation monitoring with bright light indicator. Refer to Precautions on page 49. Ordering Information Infrared light Sensing Sensing distance Output Output Cable Appearance Model method (slot width) type configuration length Dark-ON EE-SPX302-W2A 3.6 mm Light-ON EE-SPX402-W2A Dark-ON EE-SPX304-W2A 3.6 mm Light-ON EE-SPX404-W2A Through-beam NPN 1 m type output Dark-ON EE-SPX306-W2A 3.6 mm Light-ON EE-SPX406-W2A EE-SPX305-W2A Dark-ON (See note.) 5.0 mm EE-SPX405-W2A Light-ON (See note.) Note: The EE-SPX305-W2A/SPX405-W2A are not CE certified due to their internal structures. All other Photomicrosensors are CE certified. EE-SPX-W Slot-type Photomicrosensor with Cable 47Ratings/Characteristics EE-SPX302-W2A, EE-SPX402-W2A EE-SPX305-W2A Item Models EE-SPX304-W2A, EE-SPX404-W2A EE-SPX405-W2A EE-SPX306-W2A, EE-SPX406-W2A 1. The indicator is a GaP red LED Sensing distance 3.6 mm (slot width) 5 mm (slot width) (peak emission wavelength: 700 nm). 2. The response frequency was measured by Sensing object Opaque: 1 0.5 mm min. Opaque: 2 0.8 mm min. detecting the following rotating disk. Differential distance 0.05 mm max. GaAs infrared LED (pulse lighting) with a peak wavelength of Light source 940 nm Disk 2 mm 2 mm 2 mm Indicator 1 Light indicator (red) Supply voltage 5 to 24 VDC 10%, ripple (p-p): 5% max. Current consumption Average: 15 mA max. Peak: 50 mA max. EE-SPX305-W2A NPN voltage output: Load power supply voltage: 5 to 24 VDC Control output Load current: 80 mA max. Disk 80 mA load current with a residual voltage of 1.0 V max. Disk 10 mA load current with a residual voltage of 0.4 V max. Response frequency 500 Hz min. 2 3,000 lx max. with incandescent light or sunlight on the surface of Ambient illumination the receiver Operating: 10 to +55C Ambient temperature Storage: 25 to +65C EE-SPX302-W2A EE-SPX306-W2A Operating: 5% to 85% Ambient humidity Storage: 5% to 95% Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 h each Vibration resistance in X, Y, and Z directions 2 Shock resistance Destruction: 500 m/s for 3 times each in X, Y, and Z directions Enclosure rating IEC IP50 Connecting method Pre-wired (standard cable length: 1 m) Weight 18.5 g Case Material Polycarbonate Holder I/O Circuits NPN Output Output Model Timing charts Output circuit configuration Incident Interrupted Light indicator ON EE-SPX402-W2A (red) OFF EE-SPX404-W2A Output ON Light-ON transistor EE-SPX405-W2A OFF Light indicator (red) Brown Load 1 Operates EE-SPX406-W2A (relay) 1.5 to Releases 3 mA Load 1 H Load 2 Black L Main 5 to 24 VDC circuit Incident Load 2 Interrupted Blue Light indicator ON EE-SPX302-W2A (red) OFF EE-SPX304-W2A Voltage output (when the sensor is connected to a transistor circuit) Output ON Dark-ON transistor OFF EE-SPX305-W2A Load 1 Operates EE-SPX306-W2A (relay) Releases H Load 2 L 48 EE-SPX-W Slot-type Photomicrosensor with Cable