Photomicrosensor EE-SX3239-P2/-SX4239-P2 (Transmissive) Dimensions Features Note: All units are in millimeters unless otherwise indicated. Snap-in mounting model. Mounts to 1.0-, 1.2- and 1.6-mm-thick panels. Post header 175489-3 (Tyco Electronics AMP) High resolution with a 0.5-mm-wide sensing aperture. With a 5-mm-wide slot. Photo IC output signals directly connect with C-MOS and TTL. (2.4), Aperture 0.5, Connects to Tyco Electronics AMPs CT-series connectors. width Aperture width Absolute Maximum Ratings (Ta = 25C) Item Symbol Rated value Power supply voltage V 7 V CC Output voltage V 28 V OUT Output current I 16 mA OUT Permissible output P 250 mW OUT dissipation (see note) Ambient Operating Topr 20C to Note: The asterisked dimen- temperaturep 75C sion is specified by datum Storage Tstg 40C to A only. Internal Circuit 85C Unless otherwise specified, the V Soldering temperature Tsol --- tolerances are as shown below. O Note: Refer to the temperature rating chart if the ambient temperature exceeds 25C. Dimensions Tolerance G 3 mm max. 0.3 Terminal No. Name 3 mm 6 0.375 V Power supply 6 mm 10 0.45 (Vcc) 10 mm 18 0.55 O Output (OUT) 18 mm 30 0.65 G Ground (GND) Recommended Mating Connectors: Tyco Electronics AMP 175778-3 (crimp-type connector) 173977-3 (press-fit connector) Electrical and Optical Characteristics (Ta = 25C, V = 5 V 10%) CC Item Symbol Value Condition Current consumption I 16.5 mA max. With and without incident CC Low-level output voltage V 0.35 V max. I = 16 mA OL OUT without incident (EE-SX3239-P2), with incident (EE-SX4239-P2) High-level output voltage V (V x 0.9) V min. V = V with incident (EE-SX3239-P2), OH CC OUT CC without incident (EE-SX4239-P2), R = 47 k L Response frequency f 3 kHz min. V = V , R = 47 k (see note) OUT CC L Note: The value of the response frequency is measured by rotating the disk as shown below. Disk 2.1 mm 0.5 mm 0.5 mm t = 0.2 mm 186EE-SX3239-P2/-SX4239-P2 EE-SX3239-P2/-SX4239-P2 Engineering Data Output Allowable Dissipation vs. Sensing Position Characteristics Ambient Temperature Characteristics (Typical) V = 5 V d = 00.3 mm CC 1 Ta = 25C R = 47 k L (OFF) Center of optical axis (ON) Ambient temperature Ta (C) Distance d (mm) Recommended Mounting Holes When mounting the Photomicrosensor to a panel with a hole After mounting the Photomicrosensor to any panel, make sure opened by pressing, make sure that the hole has no burrs. The that the Photomicrosensor does not wobble. mounting strength of the Photomicrosensor will decrease if the When mounting the Photomicrosensor to a molding with a hole, hole has burrs. make sure that the edges of the hole are sharp enough, When mounting the Photomicrosensor to a panel with a hole otherwise the Photomicrosensor may fall out. opened by pressing, be sure to mount the Photomicrosensor on the pressing side of the panel. The mounting strength of the Photomicrosensor will increase if the Photomicrosensor is mounted to a panel with a hole that is only a little larger than the size of the Photomicrosensor, in which case, however, it will be difficult to mount the Photomicrosensor to the panel. The mounting strength of the Photomicrosensor will decrease if the Photomicrosensor is mounted to a panel with a hole that is comparatively larger than the size of the Photomicrosensor, in which case, however, it will be easy to mount the Photomicrosensor to the panel. When mounting the Photomicrosensor to a panel, open an appropriate hole for the Photomicrosensor according to the application. 187 Output allowable dissipation Pc (mW) Output transistor Light interrupting plate